在复合材料液体成型工艺过程中，通过计算机软件的模拟研究，可以预先判断树脂在增强体中的流动形式和获得树脂的注模时间以及注模压力，进而为实际成型工艺提供参考设计。本文利用 PAM-RTM 模拟软件对复合材料副翼典型结构件的树脂流动过程进行了模拟计算。根据达西定律推导出树脂在增强纤维中一维流动渗透率计算公式，分别对增强纤维、缝线纤维进行了渗透率测试，在此基础上对渗透率数值进行了修正。利用渗透率修正值采用不同的流道设计方案对树脂注模过程进行了模拟研究，根据模拟结果最终选择合理的注射方式和流道布局。对所选方案进行了工艺试验验证，并对结构件进行了超声无损检测。结果显示：理论充模时间和试验充模时间基本一致，结构件没有内部缺陷，树脂填充完全，模拟工艺计算有效。
In the process of composites fluid molding,the filling time and pressure of resin can be forecasted with using computer-aided simulation software,which can provide reference design for the real molding process of resin flow.The simulation of the resin flow had been carried out for flap structural composite by using PAM-RTM software.According to the Darcy’s law,the formula of permeability was deduced when the resin flow along reinforce fiber.The permeability of carbon fiber and suture fiber was tested and revised respec-tively.The simulation of the resin flow was carried out by using several runner means.The final reasonable injection port and runner were chosen according to simulation results.The chosen means were verified by the process experims,also the structural component was tested by using ultrasonic nondestructive testing.The results show that the theoretical filling time is almost consistent with the fill-ing time measured by the experiments.It is not found that the internal defect is existed in structural components.The resin filling is e-nough,to prove that the simulation is valid.
参考文献
| [1] | 赵晨辉,张广成,张悦周.真空辅助树脂注射成型（VARI）研究进展[J].玻璃钢/复合材料,2009(01):80-84. |
| [2] | 魏俊伟,张用兵,郭万涛.真空辅助成型（VARI）工艺研究进展[J].材料开发与应用,2010(03):99-105. |
| [3] | 赵渠森,赵攀峰.VARI真空辅助成型技术[C].复合材料—生命、环境与高技术（第12届全国复合材料学术会议：论文专辑）,2002:701-716. |
| [4] | 赵艳文,叶宏军,翟全胜,顾轶卓,李敏,张佐光.碳纳米管/玻纤/环氧层板超声真空灌注工艺及性能研究[J].航空材料学报,2013(04):58-63. |
| [5] | 洪晓斌,谢凯,刁岩,肖加余.真空辅助成型（VARI）用低黏度环氧树脂研究进展[J].化工新型材料,2006(08):11-13. |
| [6] | 李小兵,孙占红,曹正华.真空辅助树脂灌注配套基体树脂的制备及性能[J].热固性树脂,2006(01):4-7. |
| [7] | 赵晨辉,张广成,李莎莎.玻纤编织布复合材料VARI工艺中树脂流动行为研究[J].工程塑料应用,2012(02):65-68. |
| [8] | 顾宜;鲁在君;谢美丽 等.开环聚合酚醛树脂与纤维增强复合材料[P].中国,CN1115772A,1994. |
| [9] | 陈亚莉.复合材料成型工艺在A400M军用运输机上的应用[J].航空制造技术,2008(10):32-35. |
| [10] | 王新庆,孙占红,刘强,曹正华,陈静,潘翠红.BA9914 耐高温VARI 成型树脂性能研究[C].第17届全国复合材料学术会议论文集,2012:451-453. |
| [11] | Ryosuke Matsuzaki;Seiji Kobayashi;Akira Todoroki .Flow control by progressive forecasting using numerical simulation during vacuum-assisted resin transfer molding[J].Composites, Part A. Applied science and manufacturing,2013(2):79-87. |
| [12] | 魏俊伟,成天健,郭万涛.泡沫夹芯结构复合材料VARI工艺模拟研究[J].工程塑料应用,2012(04):33-38. |
| [13] | 魏俊伟,郭万涛,张用兵.夹芯结构复合材料构件VARI工艺仿真计算与成型实验[J].材料开发与应用,2012(02):51-58. |
| [14] | 刘强,赵龙,黄峰,高艳秋,吴刚,赵攀峰.基于PAM-RTM软件对VARI工艺流道模拟研究[C].第十四届全国复合材料学术会议论文集(下),2006:1016-1020. |
| [15] | 成天健,鲁先孝,张兴刚.复合材料增强纤维渗透率测量及VARI成型工艺仿真计算研究[J].工程塑料应用,2011(07):38-40. |
| [16] | 纵海,苏跃增,俞炜,周持兴.典型曲面构件的VARI工艺模拟分析及实验验证[J].高分子材料科学与工程,2010(11):156-159. |
| [17] | 罗云烽;段跃新;王伟.VIP 工艺中 L 型构件渗透规律的实验研究[J].材料工程,2009(增刊 2):15-19. |
| [18] | 杨孚标;杨金水;彭超义 等.纤维织物面外渗透率的测试方法[P].中国,101819129 B,2011. |
| [19] | LAURENT J;FRANCOIS T.Simulation of the manufac-turing of an ambulance roof by vacuum assisted resin infu-sion (VARI)[A].,2002:9:1-9:6. |
| [20] | 姜茂川;赵龙;刘强 等.VARI 液体成型工艺制备复合材料帽形泡沫夹芯构件的工艺模拟及验证[J].复合材料学报,2013,30:266-272. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%