欢迎登录材料期刊网

材料期刊网

中国科学院金属研究所 科学出版社
高级检索
  1. 首页
  2. 期刊
  3. 材料导报
  4. 大塑性变形制备铝、镁基颗粒增强复合材料的研究进展

材料导报, 2015, 29(9): 44-49. doi: 10.11896/j.issn.1005-023X.2015.09.006

大塑性变形制备铝、镁基颗粒增强复合材料的研究进展

廖文骏 1, , 王渠东 2, , 郭炜 3, , 张利 4, , 周浩 5,

1.上海交通大学轻合金精密成型国家工程研究中心,上海200240;上海交通大学金属基复合材料国家重点实验室,上海200240

2.上海交通大学轻合金精密成型国家工程研究中心,上海200240;上海交通大学金属基复合材料国家重点实验室,上海200240

3.上海交通大学轻合金精密成型国家工程研究中心,上海200240;上海交通大学金属基复合材料国家重点实验室,上海200240

4.上海交通大学轻合金精密成型国家工程研究中心,上海200240;上海交通大学金属基复合材料国家重点实验室,上海200240

5.上海交通大学轻合金精密成型国家工程研究中心,上海200240;上海交通大学金属基复合材料国家重点实验室,上海200240

基金项目:   中国博士后科学基金(2014M561466)   上海市博士后科研资助计划资助项目(14R21411000)   国家自然科学基金(51074106,51374145,51404151)   上海市科学技术委员会资助项目(09JC1408200)  

关键词： 大塑性变形 , 镁合金 , 铝合金 , 颗粒增强复合材料 , 超细晶

Severe Plastic Deformation for Al and Mg Matrix Composites with Particulate Reinforcements : A Survey

Keywords： severe plastic deformation , magnesium alloy , aluminum alloy , particulate reinforced composite , ultrafine grain

综述了目前大塑性变形(SPD)制备铝、镁基颗粒增强复合材料工艺的研究进展;总结了在SPD过程中复合材料增强颗粒的细化、再分布及基体合金晶粒的超细化等组织演变特点;分析了经SPD加工后铝、镁基颗粒增强复合材料的强韧化机制以及其力学性能的提升空间.最后指出了SPD制备颗粒增强复合材料尚存在的问题及可能的发展方向.

参考文献

[1] S.-B. Yi;C.H J. Davies;H.-G. Brokmeier .Deformation and texture evolution in AZ31 magnesium alloy during uniaxial loading[J].Acta materialia,2006(2):549-562.
[2] Ibrahim I A;Mohamed F A;Lavernia E J .Particulate reinforced metal matrix composites-A review[J].Journal of Materials Science,1991,26(05):1137.
[3] Kun Wu .Microstructure and mechanical properties of SiCp/AZ91 composite deformed through a combination of forging and extrusion process[J].Materials & design,2010(8):P.3929.
[4] Kapoor R;Vecchio K S .Deformation behavior and failure mechanisms in particulate reinforced 6061 Al metal-matrix composites[J].Mater Sei Eng A,1995,202(1-2):63.
[5] Valiev RZ.;Alexandrov IV.;Islamgaliev RK. .Bulk nanostructured materials from severe plastic deformation [Review][J].Progress in materials science,2000(2):103-189.
[6] Valiev R .Materials science - Nanomaterial advantage[J].Nature,2002(6910):887,889-0.
[7] Valiev R Z .Paradoxes of severe plastic deformation[J].Advancde Engineering Materials,2003,5(05):296.
[8] Chu H S;Liu K S;Yeh J W .Aging behavior and tensile properties of 6061Al-0.3 μm Al2O3p particle composites produced by reciprocating extrusion[J].Scripta Materialia,2001,45(05):541.
[9] Pekguleryuz M;Karl Kainer;Ali Kaya.Fundamentals of magnesium alloy metallurgy[M].Cambridge:Woodhead Publishing,2013:317.
[10] Y. Estrin;A. Vinogradov .Extreme grain refinement by severe plastic deformation: A wealth of challenging science[J].Acta materialia,2013(3):782-817.
[11] A. Azushima;R. Kopp;A. Korhonen;D. Y. Yang;F. Micari;G. D. Lahoti;P. Groche;J. Yanagimoto;N. Tsuji;A. Rosochowski;A. Yanagida .Severe plastic deformation (SPD) processes for metals[J].CIRP Annals,2008(2):716-735.
[12] Ruslan Z. Valiev;Yuri Estrin;Zenji Horita .Producing Bulk Ultrafine-Grained Materials by Severe Plastic Deformation[J].JOM,2006(4):33-39.
[13] Ruslan Z. Valiev;Terence G. Langdon .Principles of equal-channel angular pressing as a processing tool for grain refinement[J].Progress in materials science,2006(7):881-981.
[14] Han B Q;Langdon T G .Achieving enhanced tensile ductility in an Al-6061 composite processed by severe plastic deformation[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2005,410-411:430.
[15] Hassani A;Zabihi M .High strain rate superplasticity in a nano-structured Al-Mg/SiCP composite severely deformed by equal channel angular extrusion[J].Materials and Design,2012,39:140.
[16] 孙有平 .塑性变形对喷射沉积7090Al/SiC<,p>复合材料SiC分布及组织性能影响[D].湖南大学,2009.
[17] Chen L J;Ma C Y;Stoica G M et al.Mechanical behavior of a 6061 Al alloy and an Al2O3/6061 Al composite after equal-channel angular processing[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2005,410:472.
[18] Lillo TM .Enhancing ductility of AL6061+10 wt.% B4C through equal-channel angular extrusion processing[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2005(0):443-446.
[19] W. Xu;X. Wu;T. Honma .Nanostructured Al-Al_2O_3 composite formed in situ during consolidation of ultrafine Al particles by back pressure equal channel angular pressing[J].Acta materialia,2009(14):4321-4330.
[20] Tokunaga T;Kaneko K;Horita Z .Production of aluminum-matrix carbon nanotube composite using high pressure torsion[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2008,490(01):300.
[21] Tomoharu Tokunaga;Kenji Kaneko;Keisuke Sato .Microstructure and mechanical properties of aluminum-fullerene composite fabricated by high pressure torsion[J].Scripta materialia,2008(9):735-738.
[22] Christian W. Schmidt;Catharina Knieke;Verena Maier .Accelerated grain refinement during accumulative roll bonding by nanoparticle reinforcement[J].Scripta materialia,2011(3):245-248.
[23] Roohollah Jamaati .High-strength and highly-uniform composite produced by anodizing and accumulative roll bonding processes[J].Materials & design,2010(10):P.4816.
[24] Liu FR;Chan KC;Tang CY .Effect of reinforcement morphology on deformation behavior of particle reinforced metal matrix composites in laser forming[J].Computational Materials Science,2007(1):168-177.
[25] Kavosi, J.;Saei, M.;Kazeminezhad, M..Dislocation density and flow stress modeling of nanostructured Al-SiC _p composite during accumulative roll bonding[J].Computational Materials Science,2013:359-363.
[26] Guo, W.;Wang, Q.;Ye, B.;Li, X.;Liu, X.;Zhou, H..Microstructural refinement and homogenization of Mg-SiC nanocomposites by cyclic extrusion compression[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2012:267-270.
[27] ChuH S;LiuKS;YehJ W .An in situ composite of Al (graphite,Al4C3) produced by reciprocating extrusion[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2000,277(01):25.
[28] Chu H.S.;Liu K.S. .Study of 6061 -Al_2O_(3p) Composites Produced by Reciprocating Extrusion[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2000(10):2587-2596.
[29] Guo W;Wang Q D;Ye B et al.Enhanced microstructure homogeneity and mechanical properties of AZ31-Si composite by cyclic closed-die forging[J].Journal of Alloys and Compounds,2013,552:409.
[30] Reihanian M;Hadadian F K;Paydar M H .Fabrication of Al-2vol% Al2 O3/SiC hybrid composite via accumulative roll bonding (ARB):An investigation of the microstructure and mechanical properties[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2014,607:188.
[31] Toroghinejad M R;Jamaati R;Nooryan A et al.Hybrid composites produced by anodizing and accumulative roll bonding (ARB) processes[J].CERAMICS INTERNATIONAL,2014,40(07):10027.
[32] Alizadeh M;Paydar M H .Fabrication of nanostructure Al/SiCP composite by accumulative roll-bonding (ARB) process[J].Journal of Alloys and Compounds,2010,492(01):231.
[33] Erman, A.;Groza, J.;Li, X.;Choi, H.;Cao, G..Nanoparticle effects in cast Mg-1wt% SiC nano-composites[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2012:39-43.
[34] Clyne T W;Withers P J.An introduction to metal matrix composites[M].Cambridge:Cambridge University Press,1993
[35] Alizadeh M;Beni H A;Ghaffari M et al.Properties of high specific strength Al-4wt.％ Al2O3/B4 C nano-composite produced by accumulative roll bonding process[J].Materials and Design,2013,50:427.
[36] Yan Y W;Geng L;Li A B .Experimental and numerical studies of the effect of particle size on the deformation behavior of the metal matrix composites[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2007,448(01):315.
[37] Arsenault R J;Wang L;Feng C R .Strengthening of composites due to microstructural changes in the matrix[J].ACTA METALLURGICA ET MATERIALIA,1991,39(01):47.
[38] Shi-Ying Yuan;Jien-Wei Yeh;Chun-Huei Tsau .Improved microstructures and mechanical properties of 2024 aluminum alloy produced by a reciprocating extrusion method[J].Materials transactions,1999(3):233-241.
[39] K.K. Deng;K. Wu;X.J. Wang;Y.W. Wu;X.S. Hu;M.Y. Zheng;W.M. Gan;H.G. Brokmeier .Microstructure evolution and mechanical properties of a particulate reinforced magnesium matrix composites forged at elevated temperatures[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2010(6):1630-1635.
[40] J. METAYER,叶兵,郭炜,王渠东,周浩,F. MOLLET.循环闭式模锻制备Mg-Si合金的组织和力学性能[J].中国有色金属学报（英文版）,2014(01):66-75.
[41] Toroghinejad M R;Jamaati R;Nooryan A et al.The effect of alumina content on the mechanical properties of hybrid composites fabricated by ARB process[J].CERAMICS INTERNATIONAL,2014,40(07):10489.
[42] 魏斌 .（SIC<,p>/AZ91D）镁基复合材料制备工艺的研究[D].南京理工大学,2004.
[43] Akbari Beni H;Alizadeh M;Ghaffari M et al.Investigation of grain refinement in Al/Al2O3/B4C nano-composite produced by ARB[J].COMPOSITES PART B-ENGINEERING,2014,58:438.
[44] Jamaati R;Toroghinejad M R;Dutkiewicz J et al.Investigation of nanostructured Al/Al2O3 composite produced by accumulative roll bonding process[J].Materials and Design,2012,35:37.
[45] Deng K;Wang C;Shi J et al.Microstructure evolution mechanism of micron particle reinforced magnesium matrix composite at room temperature[J].Materials Chemistry and Physics,2012,134(02):581.
[46] Wert J A;Paton N;Hamilton C et al.Grain refinement in 7075 aluminum by thermomechanical processing[J].METALLURGICAL TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE,1981,12(07):1267.
[47] Deng, K.K.;Wang, X.J.;Zheng, M.Y.;Wu, K..Dynamic recrystallization behavior during hot deformation and mechanical properties of 0.2μm SiCp reinforced Mg matrix composite[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2013:824-830.
[48] Radi Y;Mahmudi R .Effect of Al2O3 nano-particles on the microstructural stability of AZ31 Mg alloy after equal channel angular pressing[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2010,527(10):2764.
[49] Xia X S;Huang J;Zhang R C et al.Evolution of microstructure and mechanical properties of AZ61 Mg alloy during cyclic closed die forging[J].MATERIALS RESEARCH INNOVATIONS,2013,17(z1):130.
[50] Zhang Z M;Xu C J;Guo X F et al.Reciprocating extrusion of in situ Mg2Si reinforced Mg-Al based composite[J].Acta Metall Sin (English Lett),2008,21(03):169.
[51] Jamaati, R.;Amirkhanlou, S.;Toroghinejad, M.R.;Niroumand, B. .Effect of particle size on microstructure and mechanical properties of composites produced by ARB process[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2011(4/5):2143-2148.
[52] Joo, S.-H.;Yoon, S.C.;Lee, C.S.;Nam, D.H.;Hong, S.H.;Kim, H.S. .Microstructure and tensile behavior of Al and Al-matrix carbon nanotube composites processed by high pressure torsion of the powders[J].Journal of Materials Science,2010(17):4652-4658.
[53] S.J. Yoo;S.H. Han;W.J. Kim .Magnesium matrix composites fabricated by using accumulative roll bonding of magnesium sheets coated with carbon-nanotube- containing aluminum powders[J].Scripta materialia,2012(2):129-132.
[54] Xing ZP.;Kang SB.;Kim HW. .Structure and properties of AA3003 alloy produced by accumulative roll bonding process[J].Journal of Materials Science,2002(4):717-722.
[55] Y. Saito;N. Tsuji;H. Utsunomiya;T. Sakai;R. G. Hong .Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process[J].Scripta materialia,1998(9):1221-1227.
[56] Hansen N;Huang X;Ueji-R et al.Structure and strength after large strain deformation[J].MATERIALS SCIENCE & ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2004,387:191.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
作者相关
文章评分
  • 您的评分：
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%

版权所有©2010中国科学院金属研究所中国科技出版传媒股份有限公司

本系统由北京仁和汇智信息技术有限公司设计开发

技术支持：info@rhhz.net