采用真空导入模塑工艺(VIMP)制备纤维增强聚合物基复合材料多墙结构件时,多墙体拐角处的纤维弯曲变形可能导致多墙体局部渗透特性发生变化.通过可视化流动实验考察了拐角对多墙体渗透特性和树脂流动行为的影响.结果表明:无论是否使用导流介质,多墙体中的拐角对树脂流体在VIMP灌注过程中都具有局部阻力作用,降低了树脂充模流动速度和多墙体整体表观渗透率,即存在拐角效应;拐角处铺放导流介质能有效降低拐角效应;随着拐角到注胶口的距离增大,整体表观渗透率表现为先下降后上升.
参考文献
| [1] | 罗楚养;熊峻江;益小苏;张子龙;刘刚.RTM整体成型复合材料翼盒的固有模态及稳定性[J].复合材料学报,2012(3):158-166. |
| [2] | 苏峰;于洋;于柏峰.真空辅助树脂灌注工艺的创新性改进[J].纤维复合材料,2010(1):18-20. |
| [3] | MD AFENDI;W. M. BANKS;D. KIRKWOOD.Bubble free resin for infusion process[J].Composites, Part A. Applied science and manufacturing,20056(6):739-746. |
| [4] | 孙赛;刘木金;王海;崔天放.RTM成型工艺及其派生工艺[J].宇航材料工艺,2010(6):21-23. |
| [5] | 杨金水 .真空导入模塑工艺树脂流动行为研究[D].国防科学技术大学,2007. |
| [6] | Andersson M;Lundstrom S;Gebart B R.Development of guidelines for the vacuum infusion process[A].Cambridge:Woodhead Publishing Materials,2000:113. |
| [7] | Lewit S M;Jakubowski J C.Low cost VARTM process for commercial and military applications[J].Society for the Advancement of Material and Process Engineering,199742(02):1173-1187. |
| [8] | Riqas E J;Walsh S M;Spurgeon W.Development of a novel processing technique for vacuum assisted resin transfer molding(VARTM)[A].New York:Technomic Publishing Co.,Inc,2001:1086-1094. |
| [9] | Pike T;McArthur M;Schade D.Vacuum assisted resin transfer molding of a layered structural laminate for application on ground combat vehicles[J].Technology Transfer in a Global Community,199628(04):374-380. |
| [10] | 杨金水 .厚截面碳纤维复合材料VIMP工艺制备与性能研究[D].国防科学技术大学,2012. |
| [11] | 陈鹏;段跃新;梁志勇.预成型体纵向渗透率统计模型[J].复合材料学报,2004(2):105-110. |
| [12] | 林建忠;阮晓东;陈邦国.流体力学[M].北京:清华大学出版社,2005:223-244. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%