为缩减获得复合材料设计许用值的试验成本，首先，介绍了复合材料手册-17-G最新推荐的一种基于回归分析的合并多环境样本的B基准值统计方法，重点阐述了在批间变异检验、环境样本间的方差等同性检验及正态性检验中加入工程经验判断的合理性及适用条件；然后，根据该多环境样本合并方法，设计开发了 B基准值统计分析软件；最后，采用该软件对江苏恒神股份有限公司部分复合材料的力学性能数据进行了统计分析。结果表明：与传统的单环境样本统计程序相比，该多环境样本合并方法不仅显著提高了 B基准值，而且克服了传统统计程序中对样本数量及批次数的限制。所得结论表明该方法具有较高的可操作性，适用于在缩减样本的情况下统计分析复合材料B基准值。
In order to reduce the test cost for obtaining the design allowables of composites,a regression analysis-based B-basis value statistical method merging multiple condition samples which was latest issued by Composite Ma-terial Handbook-17-G was introduced,and the rationality and applicable conditions for the addition of engineering experience j udgment in the check of variation between batches,the equality check for square deviation between con-dition samples and the normality check were expounded emphatically.Then,the software for statistical analysis of B-basis value was developed based on the merging method of multiple condition samples.Finally,the software was used to statistically analyze the mechanical properties data of partial Jiangsu Hengshen Company Limited compos-ites.The results show that comparing with the traditional single condition sample statistic program,the multiple condition samples merging method not only raises the B-basis value significantly,but also overcomes the limitation for number of samples and number of batches in traditional statistic program.The conclusions obtained show that this method has higher operability,and is applicable to the statistical analyses for B-basis values of composites in the case of reduced sample.
参考文献
| [1] | 马立敏;张嘉振;岳广全;刘建光;薛佳.复合材料在新一代大型民用飞机中的应用[J].复合材料学报,2015(2):317-322. |
| [2] | 李辉;张立同;曾庆丰;徐永东;成来飞;董宁;吴守军.2D C/SiC复合材料的可靠性评价[J].复合材料学报,2007(4):95-100. |
| [3] | 杨旭;何为;韩涛;王进.低速冲击下复合材料层板压缩许用值[J].复合材料学报,2014(6):1626-1634. |
| [4] | 王亮;王海鹏;吴安民.复合材料破坏数据B基准值计算的程序设计[J].理化检验-物理分册,2010(7):443-444,464. |
| [5] | 杜宝江;季长芹;郭京敏;孙安波;魏雄.航空用某复合材料力学特性统计分布的研究[J].兵器材料科学与工程,2012(3):30-33. |
| [6] | 马鑫;关志东;薛斌;刘露.复合材料B基准值计算程序[J].制造业自动化,2011(21):83-87,92. |
| [7] | 孙坚石;叶强.复合材料力学性能数据B基准值计算程序[J].航空制造技术,2009(z1):19-21,24. |
| [8] | 王翔;陈新文;王海鹏;邓立伟.基于统计的复合材料B基准值计算方法研究[J].失效分析与预防,2010(4):210-215. |
| [9] | 董本正;李伟;高丽红;郭朝龙;査萌;吉爱红;戴振东.基干Matlab的碳纤维复合材料的B基准值算法[J].现代电子技术,2014(16):87-91. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%