欢迎登录材料期刊网

材料期刊网

中国科学院金属研究所 科学出版社
高级检索
  1. 首页
  2. 期刊
  3. 表面技术
  4. 基体表面异质材料滚动接触疲劳性能与失效机理的研究进展

表面技术 , 2015, (5): 111-128. doi: 10.16490/j.cnki.issn.1001-3660.2015.05.021

基体表面异质材料滚动接触疲劳性能与失效机理的研究进展

林丽 1, , 李国禄 2, , 王海斗 3, , 康嘉杰 4,

1.河北工业大学 材料科学与工程学院,天津,300130

2.河北工业大学 材料科学与工程学院,天津,300130

3.装甲兵工程学院 装备再制造技术国家重点实验室,北京,100072

4.中国地质大学 北京 工程技术学院,北京,100083

基金项目:   973 Project(2011CB013405)   国家自然科学基金(51275151)   国家973计划(2011CB013405)   国家杰出青年科学基金(51125023) Fund:Supported by the National Natural Science Foundation of China(51275151)   Distinguished Young Scholars of NS-FC(51125023)  

关键词： 滚动接触疲劳 , 涂覆工艺 , 材料体系 , 后处理工艺

Investigation of RCF Properties and Failure Mechanism of Heterogeneous Materials Covered on the Substrate:A Review

Keywords： rolling contact fatigue , coating process , material system , post-processing method

滚动接触疲劳性能是评价膜层性能的重要指标之一。影响零件滚动接触疲劳性能的因素主要分为膜层自身结构完整性和服役条件两大类。膜层自身结构完整性又受制于涂覆工艺、材料体系、后处理方式等因素。在服役工况确定的情况下，膜层自身结构完整性对零件的接触疲劳性能起决定性的作用。不同的涂覆工艺、材料体系、后处理方式对零件的滚动接触疲劳性能及失效机理的影响不尽相同。本文综述了涂覆工艺、材料体系、后处理方式对基体表面异质材料滚动接触疲劳性能与失效机理的影响，发现对滚动疲劳失效机理也存在作用。最后，总结了目前关于膜层滚动接触疲劳研究中存在的问题，探讨了解决问题的方法，以期为基体表面膜层的接触疲劳寿命预测奠定良好的基础。

ABSTRACT:The rolling contact fatigue performance is one of the important indexes of evaluating the membrane layer perform-ance. The factors affecting the rolling contact fatigue performance of parts are mainly divided into the structural integrity of the membrane layer itself and the service conditions. The structural integrity of the layer itself is subjected to the factors of diverse coat-ing process, material system and post-processing method, and so on. When the service condition is fixed, the structural integrity of the layer itself plays a decisive role in contact fatigue performance. Diverse coating process, material system and post-processing method have different influence on the rolling contact fatigue performance and failure mechanism of the parts. The influences of the coating process, material system and post-processing method on the rolling contact fatigue performance of heterogeneous material on the substrate surface were summarized in this paper. It could be found that the factors of coating process, material system, post-processing mode also had an effect on the rolling fatigue failure mechanisms. Finally, the existing problems of current research a-bout the rolling contact fatigue of membrane layer were summarized, as well as the solve methods, in order to build good foundation for predicting contact fatigue life of substrate surface membrane layer.

参考文献

[1] Ali Beheshti;M. M. Khonsari .On the prediction of fatigue crack initiation in rolling/sliding contacts with provision for loading sequence effect[J].Tribology International,2011(12):1620-1628.
[2] 李旭东,张仕朝,庞长涛.材料滚动接触疲劳试验研究[J].航空精密制造技术,2011(03):5-7.
[3] Du LZ;Xu BS;Dong SY;Zhang WG;Zhang JM;Yang H;Wang HJ .Sliding wear behavior of the supersonic plasma sprayed WC-Co coating in oil containing sand[J].Surface & Coatings Technology,2008(15):3709-3714.
[4] 徐滨士.再制造工程基础及应用[M].哈尔滨:哈尔滨工业大学出版社,2005
[5] 王海斗;康嘉杰;濮春欢.表面涂层加速寿命试验技术[M].北京:人民邮电出版社,2011
[6] 池来俊,樊自拴,肖旭东,吴旭,孙冬柏.热喷涂高温抗氧化耐磨损涂层的研究[J].表面技术,2009(02):37-41,88.
[7] J. Jurenka;M. ?paniel.Advanced FE model for simulation of pitting crack growth[J].Advances in engineering software,2014:218-225.
[8] 朴钟宇,徐滨士,王海斗,濮春欢.等离子喷涂铁基涂层的接触疲劳失效机理研究[J].材料工程,2009(11):69-73.
[9] Wang Hai-dou;Xu Bin-shi;Liu Jia-jun;Zhuang Da-ming .Characterization and anti-friction on the solid lubrication MoS_2 film prepared by chemical reaction technique[J].Science and technology of advanced materials,2005(5):535-539.
[10] Masahiro Fujii;Akira Yoshida;Jiabin Ma;Sadato Shigemura;Kazumi Tani .Rolling contact fatigue of alumina ceramics sprayed on steel roller under pure rolling contact condition[J].Tribology International,2006(9):856-862.
[11] Zhenyu Zhang;Xinchun Lu;Jianbin Luo .Tribological properties of rare earth oxide added Cr_3C_2-NiCr coatings[J].Applied Surface Science: A Journal Devoted to the Properties of Interfaces in Relation to the Synthesis and Behaviour of Materials,2007(9):4377-4385.
[12] 安家财,杜三明,肖宏滨,张永振.等离子喷涂40%ZrO2-Al2O3-13%TiO2陶瓷涂层及其摩擦磨损性能研究[J].表面技术,2011(02):4-7.
[13] 徐滨士;朱绍华.表面工程的理论与技术[M].北京:国防工业出版社,2010
[14] Masahiro Fujii;Akira Yoshida;Jiabin Ma;Sadato Shigemura;Kazumi Tani .Rolling contact fatigue of alumina ceramics sprayed on steel roller under pure rolling contact condition[J].Tribology International,2006(9):856-862.
[15] 王海斗,张志强,李国禄,徐滨士,朴钟宇.等离子喷涂层接触疲劳失效模式及失效机理的研究[J].摩擦学学报,2012(03):251-257.
[16] Jia-jie Kang;Bin-shi Xu;Hai-dou Wang;Cheng-biao Wang.Competing failure mechanism and life prediction of plasma sprayed composite ceramic coating in rolling-sliding contact condition[J].Tribology International,2014:128-137.
[17] NIEMINEN R;VUORISTO P;NIEMI K.Rolling Con-tact Fatigue Failure Mechanisms in Plasma and HVOF Sprayed WC-Co Coatings[J].WEAR,1997(212):66-77.
[18] SHENG X Y;YU S Y .Performance in Resistance to Surface Fatigue for Cr3 C2-25%NiCr Coatings by Plasma Spray and CDS Spray[J].Tribology Letters,2004,16(03):173-180.
[19] 王海军.超音速等离子与普通等离子喷涂WC-Co涂层性能的比较[A].,2004
[20] 鲍君峰,于月光,刘海飞,曾克里,任先京.三种热喷涂工艺制备WC/Co涂层性能比较[J].有色金属（冶炼部分）,2006(04):46-49.
[21] Giovanni Di Girolamo;Luciano Pilloni;Giovanni Pulci .Tribological Characterization of WC-Co Plasma Sprayed Coatings[J].Journal of the American Ceramic Society,2009(5):1118-1124.
[22] 韩志海,王海军,白宇,丁春华,徐滨士.超音速等离子喷涂制备细密柱晶结构热障涂层研究进展[J].热喷涂技术,2011(02):1-14,40.
[23] 王海军,蔡江,韩志海.超音速等离子与HVOF喷涂WC-Co涂层的冲蚀磨损性能研究[J].材料工程,2005(04):50-54.
[24] 张显程 .面向再制造的等离子喷涂层结构完整性及寿命预测基础研究[D].上海交通大学,2007.
[25] 阎兴斌,徐洮,杨生荣,薛群基.电化学沉积DLC薄膜的摩擦学性能研究[J].摩擦学学报,2003(03):169-173.
[26] 刘洪喜,王浪平,王小峰,黄磊,汤宝寅.TiC薄膜对轴承钢表面滚动接触疲劳寿命和力学性能的影响[J].金属学报,2006(11):1197-1201.
[27] P. Motte;M. Proust;J. Torres .TiN-CVD process optimization for integration with Cu-CVD[J].Microelectronic engineering,2000(1/4):369-374.
[28] CLONY K L.Chemical Vapour Deposition of Coatings[J].Progress in Materials Science,2003(48):157-170.
[29] 刘洪喜,苏海青,蒋业华,孟春蕾,林波.航空轴承表面合成DLC薄膜的结构特征和滚动接触疲劳物理模型[J].航空学报,2009(09):1769-1775.
[30] G. Fajdiga;S. Glodez;J. Kramar .Pitting formation due to surface and subsurface initiated fatigue crack growth in contacting mechanical elements[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2007(9/10):1217-1224.
[31] 朴钟宇,徐滨士,王海斗,濮春欢.涂层厚度对喷涂层疲劳磨损寿命的影响[J].摩擦学学报,2010(05):448-452.
[32] 金国,徐滨士,王海斗,李庆芬,魏世丞.电热爆炸喷涂3Cr13涂层的微观结构和微观力学性能[J].材料热处理学报,2006(01):71-74.
[33] 胡传炘.涂层技术原理及应用[M].北京:化学工业出版社,2000
[34] TOBE S;KODAMA S;MISAWA H.Rolling Contact Behav-ior of Plasma Sprayed Coating on Aluminium Alloy[A].,1990
[35] KURODA S;CLYNE T W.The Quenching Stress in Ther-mally Sprayed Coatings[J].THIN SOLID FILMS,1991(200):49-66.
[36] ZHANG X C;XU B S;WANG H D.Thermo-mechani-cal Integrity of Coatings with Residual Stresses[J].Fracture Mechanics and Applications,2004(78):225-240.
[37] SIMES T R;MELLOR S G;HILLS D A .A Note on the In-fluence of Residual Stress on Measured Hardness[J].Jour-nal of Strain Analysis,1984,19(02):135-137.
[38] AHMED R;HADFIELD M .Rolling Contact Fatigue Per-formance of Detonation Gun Coated Elements[J].Tribology International,1997,30(02):129-137.
[39] Zhongyu Piao;Binshi Xu;Haidou Wang;Chunhuan Pu .Influence of undercoating on rolling contact fatigue performance of Fe-based coating[J].Tribology International,2010(1/2):252-258.
[40] Piao Zhong-yu;Xu Bin-shi;Wang Hai-dou;Wen Dong-hui.Investigation of RCF failure prewarning of Fe-based coating by online monitoring[J].Tribology International,2014:156-160.
[41] AHMED R.Contact Fatigue Modes of HVOF Coatings[J].WEAR,2002(253):473-487.
[42] Stewart S.;Ahmed R. .Contact fatigue failure modes in hot isostatically pressed WC-12%Co coatings[J].Surface & Coatings Technology,2003(2/3):204-216.
[43] 吴臣武,黄晨光,陈光南.局部热载荷诱导热障涂层界面分层断裂问题[J].中国科学（技术科学）,2011(01):49-54.
[44] 董世运,徐滨士,胡振峰,蒋斌.n-Al2O3/Ni复合电刷镀层的接触疲劳行为[J].材料科学与工艺,2005(05):477-480.
[45] 刘洪喜,蒋业华,周荣,詹肇麟,汤宝寅.类金刚石薄膜对轴承钢表面机械性能和滚动接触疲劳寿命的影响[J].材料研究学报,2009(01):43-48.
[46] J. W. RINGSBERG;A. BERGKVIST .On propagation of short rolling contact fatigue cracks[J].Fatigue & Fracture of Engineering Materials and Structures,2003(10):969-983.
[47] MATEOS J;CUETOS J M;VIGANDE R.Tribological Properties of Plasma Sprayed and Laser Remelted 75/25 Cr3 C2/NiCr Coatings[J].Tribology International,2001(34):345-351.
[48] Morimoto J;Sasaki Y;Fukuhara S;Abe N;Tukamoto M .Surface modification of Cr3C2-NiCr cermet coatings by direct diode laser[J].Vacuum: Technology Applications & Ion Physics: The International Journal & Abstracting Service for Vacuum Science & Technology,2006(11/12):1400-1405.
[49] Zhang, XC;Xu, BS;Tu, ST;Xuan, FZ;Zhang, YK;Wang, HD;Wu, YX .Rolling contact fatigue mechanism of a plasma-sprayed and laser-remelted Ni alloy coating[J].Fatigue & Fracture of Engineering Materials & Structures,2009(2):84-96.
[50] S. Stewart;R. Ahmed;T. Itsukaichi .Contact fatigue failure evaluation of post-treated WC-NiCrBSi functionally graded thermal spray coatings[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2004(9/10):962-983.
[51] Stewart S;Ahmed R;Itsukaichi T .Rolling contact fatigue of post-treated WC-NiCrBSi thermal spray coatings[J].Surface & Coatings Technology,2005(2/3):171-189.
[52] 王韶云,李国禄,王海斗,刘金海,徐滨士,朴钟宇.重熔处理对NiCrBSi涂层接触疲劳性能的影响[J].材料热处理学报,2011(11):135-139.
[53] 张晓东,董世运,徐滨士,王志坚,闫世兴,李庆芬.激光熔覆和活化屏等离子体氮化复合涂层组织与接触疲劳性能[J].中国激光,2011(06):181-185.
[54] 安树春,程汉池,栗桌新,高晨.热喷涂涂层的重熔后处理工艺研究进展[J].表面技术,2009(02):73-77.
[55] T. Gomez-del Rio;M. A. Garrido;J. E. Fernandez;M. Cadenas;J. Rodriguez .Influence of the deposition techniques on the mechanical properties and microstructure of NiCrBSi coatings[J].Journal of Materials Processing Technology,2008(1/3):304-312.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
作者相关
文章评分
  • 您的评分：
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%

版权所有©2010中国科学院金属研究所中国科技出版传媒股份有限公司

本系统由北京仁和汇智信息技术有限公司设计开发

技术支持：info@rhhz.net