以α-Al2O3为主原料制备凝胶注模浆料, 采用浸渍工艺制备了均匀性好、强度高的网眼陶瓷材料. 研究了固相含量、分散剂与pH值等对Al2O3浆料流变特性的影响. 实验表明: 在pH=9、分散剂添加量为0.5wt%及固相体积分数为57%时, 可以获得良好流动性(粘度为140mPa·s)的浆料; 研究了聚氨酯泡沫塑料载体表面改性对浆料吸附力的作用, 采用氩等离子体处理并在丙烯酸溶液中接枝反应使聚氨酯泡沫塑料有效吸附浆料量从0.42g/cm3提高到0.71g/cm3. 制备出气孔率为86%、体积密度为0.52g/cm3、耐压强度为3.60MPa和均匀无盲孔的Al2O3泡沫陶瓷材料.
The uniform and high intensity reticulated ceramics were fabricated with α-Al2O3 slurry by gel casting injection. The influences of solids volume fractions, dispersant and pH values on the rheological behavior of α-Al2O3 reticulated ceramics were studied. Results show that when pH=9, dispersant=0.5wt%, solid volume fraction=57%, the slurry has a good fluidity, and its viscosity is 140mPa·s. By adopting the argon plasma treating process and the stem grafting of acrylic acid, the absorbed slurry values of the foaming plastics will be changed from 0.42g/cm3 to 0.71g/cm3. The reticulated ceramics fabricated have apparent porosity of 86%, volume density of 0.52g/cm3, and compressive strength of 3.60MPa.
参考文献
| [1] | |
| [2] | 钦征骑, 等．新型陶瓷材料手册. 南京: 江苏科学技术出版社. 1995. [2] 冯胜山, 陈巨乔．耐火材料, 2002, 36 (4): 235--239 . [3] 李湘洲．陶瓷, 2005, (5): 47--49. [4] 陈 哲, 等．十堰职业技术学院学报, 2003, 16 (2): 53--55. [5] 刘 辉．矿冶工程, 2003, 23 (6): 69--71. [6] 姬宏杰． 环境污染治理技术与设备, 2003, 4 (12): 73--75. [7] 张 兰． 山东陶瓷, 2004, 27 (6): 3--6. [8] 宁红军, 纪士东． 陶瓷, 2005, (6): 19--21. [9] 朱新文, 江东亮．硅酸盐通报, 2000, (3): 45--51. [10]王春玲, 纪士东． 陶瓷, 2005, (1): 6--9. [11] 刘 岩, 黄政仁, 董绍明, 等(LIU Yan, { et al)．无机材料学报(Journal Inorganic Materials), 2005, 20 (2): 305--309. [12] Brown C C, Green D J． J. Am. Soc., 1994, 77 (6): 1467--1472. [13] 周竹发, 等．材料工程, 2005, 266 (7): 55--58. [14] 仝建峰, 陈大明． 航空材料学报, 2003, 23 (3): 50--52. [15] 曹小刚, 田杰谟．多功能材料, 2001, 32 (5): 523--524 |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%