红外触摸屏是通过红外发射管和红外接收管收发红外光来进行触摸位置的判断，其工作原理决定了太阳光会对它产生干扰.采用串行扫描方式的抗强光红外触摸屏的扫描周期很长.本文采用30．072 kHz、36 kHz、38 kHz、38．4 kHz、40 kHz、48 kHz、50 kHz、51．2 kHz无源晶振分别设计并行扫描模块中红外发射管的信号源和红外接收电路的选频器.模块实现了8个检测通道的同时工作.提高了红外触摸屏抗强光能力，解决了相邻8个红外发射管同时工作而产生的串扰问题，缩短了扫描周期.
Infrared touch screen works through light emitting diode transmitting infrared light and in-frared receiver diode receiving infrared light,so the sunlight will have interference to it.Scanning pe-riod of anti-light infrared touch screens which use serial scanning mode is too long.Eight kinds of crystal ———30.072 kHz,36 kHz,38 kHz,38.4 kHz,40 kHz,48 kHz,50 kHz,51.2 kHz are used to design signal sources of infrared emission diodes.Then,the same frequency crystals are used to de-sign frequency selective circuits.The design make eight scanning units working simultaneously come true.It enhances the anti-light ability of IR touch screen and solves the problem of interference among the eight infrared transmitting diode in parallel scanning mode,reducing scan cycle.
参考文献
| [1] | 张伟;郭勇.基于ARM的红外多点触摸屏设计[J].液晶与显示,2013(5):698-702. |
| [2] | 李冬喆;陈国龙;黄子强.红外触控屏的接收单元抗干扰新技术及其验证[J].液晶与显示,2014(2):251-257. |
| [3] | 张明 .抗强光干扰的高精度红外触摸屏设计与实现[D].电子科技大学,2008. |
| [4] | Ye X L .The infrared touch screen using polarizer parallel scanning system[P].CN 101398734A,2009-4-1. |
| [5] | 张宏伟 .多触点抗强光干扰红外触摸屏的设计与验证[D].电子科技大学,2009. |
| [6] | 董冠涛 .红外线感应电子白板的设计与实现[D].长春:吉林大学,2009. |
| [7] | 曾一雄 .基于STM32的抗强光多点红外触摸屏的设计与实现[D].电子科技大学,2013. |
| [8] | 高晋占.微弱信号检测[M].北京:清华大学出版社,2011:172-214. |
| [9] | 周烨 .基于锁相放大技术的抗强光干扰红外触控技术的研究[D].电子科技大学,2011. |
| [10] | 冯致礼.晶体滤波器[M].北京:宇航出版社,1987:488-501. |
| [11] | 李毅 .可扩展抗强光红外触控模块设计与实现[D].电子科技大学,2013. |
| [12] | 高吉祥.高频电子线路[M].北京:电子工业出版社,2003:173-175. |
| [13] | 赵声衡.晶体振荡器[M].北京.科学出版社,2008:288-289. |
| [14] | Li Y;Huang Z Q;Li G Y.Research of parallel data processing,anti-light interference infrared touch technology[A].,2012:983-987. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%