利用Ti-47.5Al-2.5V-1.0Cr(%)气雾化预合金粉末为原料, 采用注射成形工艺制备了TiAl合金材料, 研究了TiAl合金烧结工艺以及烧结工艺对烧结体显微组织、密度和性能的影响. 结果表明: 烧结体在超固相线液相区烧结得到密度最高. 在1450 ℃保温30 min, 烧结体的相对密度达到95%, 抗压强度为2105 Mpa, 压缩率达到30.9%, 接近铸态合金力学性能. 烧结体在α+γ相区和α相区保温1 h, 相对密度分别为73%和85%. 在1300～1400 ℃, 随着片层团的增加, 烧结体组织由双态组织逐渐变为全片层组织. 在超固相液相区, 随着γ相的减少, 烧结体组织由近片层组织逐渐转变为全片层组织.
参考文献
| [1] | Kim Y W .Intermetallic alloys based on gamma titanium aluminide[J].Journal of the Minerals,Metals & Materials Society,1989,41:24. |
| [2] | Kim Y W;Dimiduk D M .Progress in the understanding of gamma titanium aluminides[J].Journal of the Minerals,Metals & Materials Society,1991,43:40. |
| [3] | Brossmann U-Oehring M;Appel F.Microstructure and chemical homogeneity of high Nb gamma based TiAl alloys in different conditions of processing[A].Warrendale,2001:191. |
| [4] | 曹睿,朱浩,陈剑虹,张继.TiAl基合金双态组织平板拉伸连续卸载试验的研究[J].稀有金属,2008(01):13-16. |
| [5] | 林有智,曹睿,李雷,陈剑虹,胡大为.全层TiAl基合金室温断裂机制的研究[J].稀有金属,2007(02):148-153. |
| [6] | Imaev R M;Imaev V M;Khismatullin T G .Refining of the microstructure of cast intermetallic alloy Ti-43%Al-X (Nb,Mo,B) with the help of heat treatment[J].Metal Science and Heat Treatment,2006,48:81. |
| [7] | Lee T K;Mosunov E I;Hwang S K.Consolidation of a gamma TiAl-Mn-Mo alloy by elemental powder metallurgy[J].Materials Science and Engineering,1997(04):128. |
| [8] | Kato Kiyotaka;Matsumoto Akihiro .Tensile properties at high temperature of sintered TiAl compacts by injection molding[J].Journal of the Japan Society of Powder and Powder Metallurgy,1997,44:1029. |
| [9] | 王天国,邵刚勤,段兴龙,史晓亮,孙鹏,李勇.高能球磨与热压烧结制备TiAl基合金[J].机械工程材料,2007(01):32-34. |
| [10] | 王尔德,胡连喜,李小强.高能球磨Ti/Al复合粉体的反应烧结致密行为[J].粉末冶金技术,2003(05):259-263. |
| [11] | 张绪虎,郎泽保.TiAl金属间化合物粉末冶金制备技术研究[J].宇航材料工艺,2007(05):53-55,66. |
| [12] | Terauchi;Syuntaro Teraoka.Tsuneo development of TiAl-type intermetallic compounds by metal powder injection molding process[J].Journal of the Japan Society of Powder and Powder Metallurgy,2000(47):1283. |
| [13] | Kim Yongchan;Kim Nack J.Densification behavior of PlMed TiAl parts[J].Journal of the Japan Society of Powder and Powder Metallurgy,1999(46):882. |
| [14] | Miura H;Uemura M;Kubota Y.High-temperature properties of injection molded TiAl intermetallic compounds[A].,2004:13. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%