采用热浸镀技术在Q235钢表面制备了镍基合金涂层,采用XRD和SEM-EDS研究了涂层腐蚀前后的相组成、形貌和成分,并探讨了腐蚀机理.结果表明:涂层中有多种形态的析出物,涂层与基体之间存在宽5~8μm的过渡带;盐雾试验后,涂层表面腐蚀产物为Ni(OH)2,Fe3O4和Fe+3O(OH),平均腐蚀速率大约为1.18×10-7g/(h·mm2);腐蚀首先发生在显微孔洞或析出相边界处,表现为局部腐蚀特征.
参考文献
[1] | C. R. Das;S. K. Albert;A. K. Bhaduri .A novel procedure for fabrication of wear-resistant bushes for high-temperature application[J].Journal of Materials Processing Technology,2003(1):60-66. |
[2] | Sudha C;Shankar P;Rao RS;Thirumurugesan R;Vijayalakshmi M;Raj B .Microchemical and microstructural studies in a PTA weld overlay of Ni-Cr-Si-B alloy on AISI 304L stainless steel[J].Surface & Coatings Technology,2008(10):2103-2112. |
[3] | Navas C;Colaco R;de Damborenea J;Vilar R .Abrasive wear behaviour of laser clad and flame sprayed-melted NiCrBSi coatings[J].Surface & Coatings Technology,2006(24):6854-6862. |
[4] | Conde A.;Zubiri F.;de Damborenea J. .Cladding of Ni-Cr-B-Si coatings with a high power diode laser[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2002(1/2):233-238. |
[5] | 黄柳仙,曹玉鹏,林晨,周明升,赵小军.真空熔覆镍基合金-碳化钨复合涂层的研究[J].表面技术,2009(03):25-27. |
[6] | Tadeusz Hejwowski .Investigations of Corrosion Resistance of Fe-,Ni-and Co-based Hardfacings[J].Vacuum,2006,80(11/12):1386-1390. |
[7] | Shenglin Liu .Dry sliding wear behavior and corrosion resistance of NiCrBSi coating deposited by activated combustion-high velocity air fuel spray process[J].Materials & design,2010(2):913-917. |
[8] | Zhao WM;Wang Y;Dong LX;Wu KY;Xue J .Corrosion mechanism of NiCrBSi coatings deposited by HVOF[J].Surface & Coatings Technology,2005(2/3):293-298. |
[9] | 李会谦,许跟国,马江虹,冀国娟,王梦雨.热浸镀技术及其应用[J].有色金属(冶炼部分),2008(z1):17-19. |
[10] | 方晓英,郭红.热浸镀法生产的铜包钢线性能研究[J].热加工工艺,2006(22):49-51. |
[11] | 井玉安,王晨宇.不锈钢复合板生产技术综述[J].鞍山科技大学学报,2007(06):590-594. |
[12] | 于九明,孝云祯,王群骄,方晓英,崔光洙.金属层状复合技术及其新进展[J].材料研究学报,2000(01):12-16. |
[13] | 陈永言.电化学基础[M].天津:天津科学技术出版社,1999 |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%