采用一次挤压变形、二次挤压变形以及一次挤压后再进行锻造的三种加工工艺对AZ61镁合金进行塑性变形,研究不同的加工工艺对镁合金力学性能及拉压不对称性的影响.结果表明:挤压变形可以细化AZ61镁合金的晶粒,而在挤压后进行锻造变形,会使得其晶粒长大粗化.二次挤压后,由于强化了{0002}基面织构,AZ61镁合金的拉伸屈服强度增加,压缩屈服强度下降,使得拉压不对称性加大.而一次挤压后锻造,在挤压基面织构状态得到改变,且由于晶粒粗大,从而总体上使得AZ61镁合金的拉伸屈服强度下降,而压缩屈服强度几乎保持不变,AZ61的拉压不对称性得到改善.
参考文献
| [1] | 陈振华.变形镁合金[M].北京:化学工业出版社,2005 |
| [2] | AVEDESIAN M;BAKER H.ASM Specialty Handbook-Magnesium and Magnesium Alloys[M].Ohio,USA:ASM International,1999:44-51. |
| [3] | MORDIKE B L;EBERT T .Magnesium properties-applicationspotential[J].Materials Science and Engineering A,2001,302:37-45. |
| [4] | 肖林.密排六方金属的塑性变形[J].稀有金属材料与工程,1995(06):21-28. |
| [5] | 刘庆.镁合金塑性变形机理研究进展[J].金属学报,2010(11):1458-1472. |
| [6] | M.R. Barnett;C.H.J. Davies;X. Ma .An analytical constitutive law for twinning dominated flow in magnesium[J].Scripta materialia,2005(7):627-632. |
| [7] | BALL E A;PRANGNELL P B .Tensile-compressive yield asymmetries in high strength wrought magnesium alloys[J].Scripta Metallurgica et Materialia,1994,31(02):111-116. |
| [8] | Y.N. Wang;J.C. Huang .Texture analysis in hexagonal materials[J].Materials Chemistry and Physics,2003(1):11-26. |
| [9] | 陈振华,夏伟军,程永奇,傅定发.镁合金织构与各向异性[J].中国有色金属学报,2005(01):1-11. |
| [10] | J. Swiostek;J. Goeken;D. Letzig;K.U. Kainer .Hydrostatic extrusion of commercial magnesium alloys at 100℃ and its influence on grain refinement and mechanical properties[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2006(1/2):223-229. |
| [11] | 路君,靳丽,董杰,曾小勤,丁文江,姚真裔.等通道角挤压变形AZ31镁合金的变形行为[J].中国有色金属学报,2009(03):424-432. |
| [12] | Jan Bohlen;Patrik Dobron;Jacek Swiostek;Dietmar Letzig;Frantisek Chmelik;Pavel Lukac;Karl Ulrich Kainer .On the influence of the grain size and solute content on the AE response of magnesium alloys tested in tension and compression[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(1/2):302-306. |
| [13] | ION S E;HUNPHREYS F J;WHITE S H .Dynamic recrystallisation and the development of microstructure during the high temperature deformation of magnesium[J].Acta Materialia,1982,30(12):1909-1912. |
| [14] | 崔中圻.金属学与热处理[M].北京:机械工业出版社,2000:169-181. |
| [15] | KAINER K U;DAVIES C H J;XIONG F.Magnesium Alloys and Their Applications[M].Weinheim,Germany:Wiley-VCH,2003:433-438. |
| [16] | Mamoru Mabuchi;Yasumasa Chino;Hajime Iwasaki .The Grain Size and Texture Dependence of Tensile Properties in Extruded Mg-9Al-1Zn[J].Materials transactions,2001(7):1182-1189. |
| [17] | 刘天模,刘建忠,卢立伟,袁晗琦,时秀玲,潘复生.双向双通道变通径挤压AZ31镁合金的显微组织及变形行为[J].中国有色金属学报,2010(09):1657-1664. |
| [18] | Y.J. Chen;Q.D. Wang;H.J. Roven .Network-shaped fine-grained microstructure and high ductility of magnesium alloy fabricated by cyclic extrusion compression[J].Scripta materialia,2008(4):311-314. |
| [19] | M.R. Barnett;Z. Keshavarz;A.G. Beer .Influence of grain size on the compressive deformation of wrought M-3Al-lZn[J].Acta materialia,2004(17):5093-5103. |
| [20] | BARNETT M R;NAVE M D;BETTLES C J .Deformation microstructures and textures of some cold rolled Mg alloys[J].Materials Science and Engineering A,2004,386:205-211. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%