基于碳布优异的耐热性能、摩擦磨损性能和纳米MoS2的自润滑特性，采用纳米 MoS2改性处理碳布摩擦材料以适用于高载荷、高转速或润滑不充分等特殊的工况条件.通过在树脂浸渍液中加入不同质量分数的纳米MoS2对摩擦材料进行改性处理.采用扫描电子显微镜、光学显微镜和湿式摩擦实验机等对材料的表面形貌以及摩擦磨损性能进行分析.实验结果表明，纳米MoS2的加入有利于提高材料的致密性，改善表面粗糙度；当 MoS2含量小于5％时，样品的动摩擦系数变化较小，约为2．6％，但当 MoS2含量为8％时，动摩擦系数降幅较大，达到14．2％；纳米MoS2的加入有效减少磨损过程中纤维的拔出与断裂，大幅度降低磨损率.
Based on excellent performance of carbon fabric and nano-molybdenum disulfide,the friction materi-als with different content of MoS2 were prepared to adapt the unusual operating conditions such as high rotating speed,excessive load and insufficient lubrication and so on.All samples were obtained by dipping impregnation solution with different mass fractions of nano-molybdenum disulfide.The surface morphology and tribology be-havior were investigated by scanning electron microscope (SEM),confocal optical microscope (C130)and wet friction material test machine.Experimental results showed that adding nano-molybdenum disulfide could im-prove the material density and surface roughness.The dynamic friction coefficient decreased very little only a-bout 2.6% with the MoS2 content no more than 5%,but it decreased 14.2% with 8% MoS2 .With addition of MoS2 ,the fiber pullout or fracture was significantly reduced leading to greatly decrease of the wear rate.
参考文献
| [1] | A. M. Kovalchenko;O. I. Fushchich;S. Danyluk.The tribological properties and mechanism of wear of Cu-based sintered powder materials containing molybdenum disulfide and molybdenum diselenite under unlubricated sliding against copper[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2012:106-123. |
| [2] | W. Osterle;C. Prietzel;H. Kloss;A. I. Dmitriev .On the role of copper in brake friction materials[J].Tribology International,2010(12):2317-2326. |
| [3] | 费杰,黄剑锋,曹丽云,李翠艳.炭布/树脂复合摩擦材料的湿式摩擦学性能[J].复合材料学报,2013(03):70-75. |
| [4] | Jie Fei;He-Jun Li;Jian-Feng Huang;Ye-Wei Fu.Study on the friction and wear performance of carbon fabric/phenolic composites under oil lubricated conditions[J].Tribology International,2012:30-37. |
| [5] | Xiang Z X;Dong G;Liu L et al.Study on the tribology performance of the C/Cu composite material[J].Journal of Functional Materials,1997,28(02):201-204. |
| [6] | Baiming Chen;Qinling Bi;Jun Yang;Yanqiu Xia;Jingcheng Hao .Tribological properties of solid lubricants (graphite, h-BN) for Cu-based P/M friction composites[J].Tribology International,2008(12):1145-1152. |
| [7] | H. Sarmadi;A. H. Kokabi;S. M. Seyed Reihani .Friction and wear performance of copper-graphite surface composites fabricated by friction stir processing (FSP)[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2013(1/2):1-12. |
| [8] | 费杰,李贺军,齐乐华,付业伟,李克智.石墨含量对纸基摩擦材料摩擦磨损性能的影响[J].摩擦学学报,2007(05):451-455. |
| [9] | 潘广镇,齐乐华,付业伟,费杰,张翔.石墨改性碳布复合材料湿式摩擦磨损性能研究[J].摩擦学学报,2012(04):360-366. |
| [10] | 见雪珍,李华,房光强,曾庆平,杨磊,康红梅,刘河洲.含碳纳米管、石墨烯的PTFE基复合材料摩擦磨损性能[J].功能材料,2014(03):03011-03016. |
| [11] | J. Luo;M. H. Zhu;Y. D. Wang;J. F. Zheng;J. L. Mo .Study on rotational fretting wear of bonded MoS_2 solid lubricant coating prepared on medium carbon steel[J].Tribology International,2011(11):1565-1570. |
| [12] | Tianchang Hu;Yongsheng Zhang;Litian Hu.Tribological investigation of MoS_2 coatings deposited on the laser textured surface[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2012:77-82. |
| [13] | Kubart T;Polcar T;Kopecky L;Novak R;Novakova D .Temperature dependence of tribological properties of MoS2 and MoSe2 coatings[J].Surface & Coatings Technology,2005(1/3):230-233. |
| [14] | 苏峰华,张招柱,王坤,姜葳,刘维民.MoS2和PTFE改性炭纤维织物复合材料的摩擦磨损性能研究[J].摩擦学学报,2005(04):338-342. |
| [15] | 朱鹏,王晓东,黄培,王筱,时钧.二硫化钼改性热塑性聚酰亚胺复合材料的摩擦磨损性能研究[J].摩擦学学报,2005(05):441-445. |
| [16] | Junxiang Wang;Mingyuan Gu;Bai Songhao;Shirong Ge .Investigation of the influence of MoS2 filler on the tribological properties of carbon fiber reinforced nylon 1010 composites[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2003(1/6):774-779. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%