利用旋转式冲蚀试验机对 QAl9-4铝青铜在含 SiC 沙粒的3．5％NaCl 中的冲蚀磨损行为进行了研究.结果表明，在介质流速小于28．3 m/s 时，失重量随介质流速的增加而增大；失重随沙粒粒径变化有明显的转折点，在粒径为0．3 mm时材料流失最为显著.沙粒粒径变化引起 QAl9-4铝青铜冲蚀磨损行为的变化，小粒径时以犁削磨损为主，大粒径时锻打挤压作用增强的同时犁削磨损作用减弱.
The erosion of QAl9-4 aluminum bronze has been investigated in 3.5% NaCl including SiC particles by using a rotating disk system.The results show that the mass loss increases with increasing the flow velocity when the velocity is lower than 28.3 m/s,and the mass loss vs particle size exhibits an transition point beyond which the mass loss decreases obviously,which is 0.3 mm.The variations of particle size can lead to the change of the erosion behavior of QAl9-4 aluminum bronze samples.The failure of samples is mainly attributed to the ploughing wear under condition of little particles,however,the forging and extrusion effect improves and the ploughing wear decreases under condition of big particles.
参考文献
| [1] | 周浩;杜磊;张金民.冲刷腐蚀纯铜中空位透射电镜研究[J].物理测试,2010(5):22-24. |
| [2] | 王志武;原素芳.黄铜HSn70-1A、HA177-2A的抗冲刷能力比较研究[J].中国腐蚀与防护学报,2005(3):179-182. |
| [3] | 刘勇;龙永强;刘平;田保红.液固两相介质流中Cu-Cr-Zr合金的冲蚀磨损行为[J].中国有色金属学报,2007(10):1650-1655. |
| [4] | 郑俊涛;张三平;周学杰;曾恩;胡章枝.白铜B10和B30冲刷腐蚀对比研究[J].装备环境工程,2010(1):40-43. |
| [5] | B. A. Lindsley;A. R. Marder.The effect of velocity on the solid particle erosion rate of alloys[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,19991(1):510-516. |
| [6] | 庞佑霞;陆由南;尹喜云.含沙量和沙粒粒径对QT500材料冲蚀磨损特性的影响[J].机械工程材料,2006(4):51-53. |
| [7] | M. M. Stack;J. S. James;Q. Lu.Erosion-corrosion of chromium steel in a rotating cylinder electrode system: some comments on particle size effects[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,20045(5):557-564. |
| [8] | 廖志康;刘成龙;高丹丹;李志均;黄伟九.空蚀与冲蚀联合作用下锡黄铜表面失效形貌演变[J].重庆理工大学学报（自然科学版）,2015(6):41-45,53. |
| [9] | 庞佑霞;陆由南;郝诗明.冲蚀速度对40Cr材料抗冲蚀性能影响的研究[J].润滑与密封,2007(4):112-113. |
| [10] | 王家序;陈战;秦大同.水润滑橡胶轴承的摩擦磨损特性及机理研究[J].润滑与密封,2002(4):21-23. |
| [11] | 庞佑霞;唐勇;梁亮;朱宗铭;许焰;刘厚才;李彬.冲蚀与空蚀交互磨损三相流场仿真与试验研究[J].机械工程学报,2012(3):115-120. |
| [12] | 庞佑霞;刘厚才;朱宗铭;梁亮.40Cr冲蚀与空蚀交互磨损试验研究[J].润滑与密封,2011(8):20-22,34. |
| [13] | 周青;刘成龙;廖志康;张小彬;高丹丹;黄伟九.空蚀与冲蚀交互作用下锡黄铜的材料流失及力学性能研究[J].润滑与密封,2014(8):81-85. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%