分析了板材软模成形数值模拟的特点,对目前主要采用的软模成形数值模拟方法进行了阐述和评价,并对三类典型软模成形(液压成形,橡皮成形及粘性介质压力成形)过程数值模拟应用进行了综述,最后对板材软模成形数值模拟发展趋势进行了展望.
参考文献
| [1] | F. Vollertsen;R. Breede;K. Lange .A method for deep drawing with multiple elastomer membranes[J].CIRP Annals,1999(1):221-226. |
| [2] | PARK J W;HONG Y S;LIM S H .Dieless forming apparatus[P].US 6151938,2000-11-28. |
| [3] | Daniel F. Walczyk;David E. Hardt .Design and analysis of reconfigurable discrete dies for sheet metal forming[J].Journal of Manufacturing Systems,1998(6):436-454. |
| [4] | Z.J. Wang;J.G. Liu;X.Y. Wang .Viscous pressure forming (VPF): state-of-the-art and future trends[J].Journal of Materials Processing Technology,2004(1/3):80-87. |
| [5] | THIRUVARUDCHELVAN S .Elastomers in metal forming:a review[J].Journal of Materials Processing Technology,1993,39:55-82. |
| [6] | SIEGERT K et al.Reeent Developments in Hydroforming Technology[J].Journal of Materials Processing Technology,2000,98:251-258. |
| [7] | LIU J;WESTHOFF B;AHMETOGLA M;ALTAN T .Application of viscous pressure forming (VPF) to low volume stamping of difficult-to-forming alloys-results of preliminary FEM simulations[J].Journal of Materials Processing Technology,1996,53(01):49-58. |
| [8] | SZENG T C;WU W T;TANG J P.Combined elastoplastic and rigid-viseoplastie deformation analysis with microstructure change by using rate-form finite element method[J].NAMRC XXIV |
| [9] | 张兆辉 .液压橡皮囊弯边成形过程数值模拟及试验研究[D].北京航空航天大学,1998. |
| [10] | Leonid B. Shulkin;Ronald A. Posteraro;Mustafa A. Ahmetoglu;Gary L. Kinzel;Taylan Altan .Blank holder force (BHF) control in viscous pressure forming (VPF) of sheet metal[J].Journal of Materials Processing Technology,2000(1):7-16. |
| [11] | Mustafa Ahmetoglu;Jiang Hua;Srikanth Kulukuru .Hydroforming of sheet metal using a viscous pressure medium[J].Journal of Materials Processing Technology,2004(1):97-107. |
| [12] | YANG D Y;KIM J B;LEE D W .Investigation into manufacturing of very long cups by hydromechanical deeo-drawing and ironing with controlled radial pressure[J].Annals of the CIRP,1995,44(01):255-258. |
| [13] | LOS W;HSU T C;WILSON W .An analysis of the hemispherical-punch hydroforming process[J].Journal of Materials Processing Technology,1993,37:225-240. |
| [14] | JENSEN M R .Investigation of tool wear and hydro-mechanical deep drawing[D].Aalborg University,Aalborg,Denmark,1999. |
| [15] | 徐永超 .板材液压成形工艺及其数值模拟研究[D].哈尔滨工业大学,2003. |
| [16] | 贾德财 .橡皮成形有限元模拟研究[D].南京航空航天大学,1999. |
| [17] | LIU J G;WANG Z J;WANG Z R.Formability comparison of three kinds of sheet flexible forming processes[A].陕西西安,2004 |
| [18] | GIUSEPPE S .A numerical and experimental approach to optimise sheet stamping technologies:Part Ⅱ:aluminium alloys rubber-forming[J].Materials & Design,2001,22:299-315. |
| [19] | M. Husnu Dirikolu;Esra Akdemir .Computer aided modelling of flexible forming process[J].Journal of Materials Processing Technology,2004(3):376-381. |
| [20] | WANG Z J;LIU J G;WANG Z R;LV J .Deformation behavior of sheet metals and viscous medium in viscous pressure bulging process with back viscous pressure[J].Transactions of Nonferrous Metals Society of China,2003,13(z1):136-139. |
| [21] | 王忠金;王仲仁 .板料粘性介质胀形过程应变速率变化的模拟研究[J].塑性工程学报,1999,6(03):46-48. |
| [22] | J. Liu;M. Ahmetoglu;T. Altan .Evaluation of sheet metal formability, viscous pressure forming (VPF) dome test[J].Journal of Materials Processing Technology,2000(1):1-6. |
| [23] | LIU Jian-guang;WANG Zhong-jin;WANG Zhong-ren .Numerical simulation of influence of viscous adhesive stress on viscous pressure bulging process of hemispherical sphere[J].Transactions of Nonferrous Metals Society of China,2003(6):1354-1359. |
| [24] | FUKUDA M;YAMAGUCHI K .On the coefficient of friction between rubber and metal under high pressure[J].Bulletin of the JSME,1974,17(103):157-164. |
| [25] | ZHANG L C .A mechanics model for sheet-metal stamping using deformable dies[J].Journal of Materials Processing Technology,1995,53:798-810. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%