基于有限元计算方法和量纲分析原理提出了热障涂层合理压入深度的确定方法,并研究了涂层及基体材料特性对合理压入深度的影响.首先,根据量纲分析原理提出了合理压入深度的无量纲表达式;其次基于锥形压头识别理想弹塑性材料的材料特性的方法,提出合理压入深度的确定方法;最后研究了各无量纲因素对合理压入深度的影响.研究发现基体的弹性模量对合理压入深度的影响最大,粘结层材料特性的影响较大,热氧化生成层的材料特性及基体的屈服极限对合理压入深度的影响不大.
参考文献
| [1] | 周宏明,易丹青,余志明,肖来荣.热障涂层的研究现状与发展方向[J].材料导报,2006(03):4-8. |
| [2] | 谢冬柏,王福会.热障涂层研究的历史与现状[J].材料导报,2002(03):7-10. |
| [3] | Eskner M.;Sandstrom R. .Measurement of the elastic modulus of a plasma-sprayed thermal barrier coating using spherical indentation[J].Surface & Coatings Technology,2004(0):165-171. |
| [4] | BUSHAN B.Handbook of Micro/Nanotribology[M].Boca Raton:crc Press,1999 |
| [5] | Gamonpilas C;Busso EP .On the effect of substrate properties on the indentation behaviour of coated systems[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2004(1/2):52-61. |
| [6] | Aditad Vasinonta;Jack L. Beuth .Measurement of interfacial toughness in thermal barrier coating Systems by indentation[J].Engineering Fracture Mechanics,2001(7):843-860. |
| [7] | Chungen Zhou;Na Wang;Huibin Xu .Comparison of thermal cycling behavior of plasma-sprayed nanostructured and traditional thermal barrier coatings[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(1/2):569-574. |
| [8] | JOHNSON K L.接触力学[M].北京:高等教育出版社,1992:103-149. |
| [9] | 曹学强.热障涂层材料[M].北京:科学出版社,2007:165-168. |
| [10] | ZENG Kai-yang;ROWCLIFFE DAVID .Analysis of peneration curves produced by sharp indentation on ceramic materials[J].Philosophical Magazine A:Physics of Condensed Matter:Structure,Defects and Mechanical Properties,1996,74(05):1107-1116. |
| [11] | Wellman RG.;Dyer A.;Nicholls JR. .Nano and micro indentation studies of bulk zirconia and EB PVD TBCs[J].Surface & Coatings Technology,2004(2):253-260. |
| [12] | Guo SQ;Kagawa Y .Effect of loading rate and holding time on hardness and Young's modulus of EB-PVD thermal barrier coating[J].Surface & Coatings Technology,2004(1):92-100. |
| [13] | Yanping Cao;Xiuqing Qian;Norbert Huber .Spherical indentation into elastoplastic materials: Indentation-response based definitions of the representative strain[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(0):1-13. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%