用有限元模拟方法研究了具有应变硬化行为的弹塑性材料的多道次(至多4道次)等通道转角挤压变形行为.结果表明,随着挤压道次增加,塑性变形区尺寸和对称性增加,拐角缝隙越来越小;按A路径挤压时,应变均匀性越来越差,最大塑性应变区随挤压道次增加向试样前上端移动;按C路径挤压时,应变均匀性越来越好,最大塑性应变区位于试样中心部位;挤压道次相同时,C路径累积最大塑性应变值比A路径要小.
参考文献
| [1] | SEGAL V M;REZNIKOV V I;DROBYSHEVSKIY A E et al.Plastic working of metals by simple shear[J].Russian Metallurgy,1981,1:199-105. |
| [2] | IWAHASHI Y;WANG J;HORITA Z et al.Principle ofequal-channel angular pressing for the processing of uhra fine grained materials[J].Scripta Materialia,1996,35(02):143-146. |
| [3] | Hyoung Seop Kim;Min Hong Seo;Sun Ig Hong .Finite element analysis of equal channel angular pressing of strain rate sensitive metals[J].Journal of Materials Processing Technology,2002(0):497-503. |
| [4] | Kim HS. .Finite element analysis of equal channel angular pressing using a round corner die[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2001(1/2):122-128. |
| [5] | S. Li;M.A.M. Bourke;I.J. Beyerlein .Finite element analysis of the plastic deformation zone and working load in equal channel angular extrusion[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2004(1/2):217-236. |
| [6] | Z.J. Zhang;I.H. Son;Y.T. Im .Finite element analysis of plastic deformation of CP-Ti by multi-pass equal channel angular extrusion at medium hot-working temperature[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(1/2):134-141. |
| [7] | W.J. Zhao;H. Ding;Y.P. Ren .Finite element simulation of deformation behavior of pure aluminum during equal channel angular pressing[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2005(0):348-352. |
| [8] | Kim HS. .Finite element analysis of deformation behaviour of metals during equal channel multi-angular pressing[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2002(1/2):317-323. |
| [9] | NAKASHIMA K;HORITA Z;NEMOTO M et al.Development of a multi-pass facility for equal-channel angular pressing to high total strains[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2000,281(1-2):82-87. |
| [10] | Ruslan Z. Valiev;Terence G. Langdon .Principles of equal-channel angular pressing as a processing tool for grain refinement[J].Progress in materials science,2006(7):881-981. |
| [11] | KIM H S;SEO M H;HONG S I .On the die comer gap formation in equal channel angular pressing[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2000,291(1-2):86-90. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%