测试了TC1和TC4钛合金在氢氟酸-硝酸溶液中腐蚀加工的E-t曲线和极化曲线,分析了腐蚀加工过程的速率变化,观察了腐蚀加工形貌.在氢氟酸-硝酸腐蚀加工液中,极化曲线呈现活化-钝化特征,氢氟酸浓度较高时,硝酸浓度增大到一定值后,极化曲线呈现自钝化倾向.钝化膜的生成速率和厚度由氢氟酸和硝酸体积比决定,氢氟酸和硝酸体积比为1∶2时,腐蚀加工速率最大.腐蚀加工初期钛合金表面氧化膜被破坏,自腐蚀电位迅速变负,加工速率较大,继续加工,硝酸使钛合金表面发生钝化,导致速率降低,钝化膜的生成和破坏同时进行,当钝化膜的生成与基体溶解达到动态平衡时,自腐蚀电位和加工速率趋于稳定.TC1和TC4钛合金中的Ti和Al优先溶解,随着硝酸浓度的增加,钛合金表面微观凹坑变浅.
参考文献
[1] | 陶春虎;刘庆泉;曹春晓.航空用钛合金的失效及其预防[M].北京:国防工业出版社,2002:1-3. |
[2] | 赵树萍,吕双坤.钛合金在航空航天领域中的应用[J].钛工业进展,2002(06):18-21. |
[3] | SUN J;GUO Y B .Characteristics of 3D chip morphology and properties in end milling titanium alloy Ti-6Al-4V[J].International Journal of Advanced Manufacturing Technology,2008,38(13):1-9. |
[4] | J.H. Xu;K.Q. Ren;G.S. Geng .Cutting Forces in High-speed Milling of a Close Alpha Titanium Alloy[J].Key engineering materials,2004(259/260):451-455. |
[5] | 杨丁.金属蚀刻技术[M].北京:国防工业出版社,2008:143-146. |
[6] | Armco Steel Corporation .Chemical milling process and bath therefor[P].The United Kingdoms,1304043,1973-1-24. |
[7] | McDonnell Douglas Corporation .Chemical-milling of titanium and refractory metals[P].The United States,4116755,1978-9-26. |
[8] | TAKASAKI A;FURUYA Y .Hydrogen evolution from chemically etched titanium aluminides[J].Journal of Alloys and Compounds,1996,243(1-2):167-172. |
[9] | TAKASAKI A;OJIMA K;TANEDA Y .New phase formation in titanium aluminide during chemical etching[J].Scripta Metallurgica et Materialia,1994,30(09):1095-1098. |
[10] | 张红;朱彦海.钛合金化学铣切工艺研究[J].航空工艺技术,1996(06):29-30. |
[11] | 金蕾,李获.钛合金化学铣切及电化学加工[J].稀有金属材料与工程,1989(02):66-71. |
[12] | 戚运莲,邓炬,洪权.钛和钛合金化学铣切中的吸氢及其影响[J].航空制造技术,2000(02):30. |
[13] | <航空制造工程手册>总编委会.航空制造工程手册(特种加工)[M].北京:航空工业出版社,1993:600-645. |
[14] | Lim PY;She PL;Shih HC .Microstructure effect on microtopography of chemically etched alpha plus beta Ti alloys[J].Applied Surface Science: A Journal Devoted to the Properties of Interfaces in Relation to the Synthesis and Behaviour of Materials,2006(2):449-458. |
[15] | Say WC.;Tsai YY. .Surface characterization of cast Ti-6Al-4V in hydrofluoric-nitric pickling solutions[J].Surface & Coatings Technology,2004(3):337-343. |
[16] | 林翠,蔡剑,曾丰光,黄茜,杜楠,赵晴.LY12铝合金化铣工艺及加工质量影响因素[J].失效分析与预防,2010(01):8-12,16. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分:
-
10%
-
20%
-
30%
-
40%
-
50%