欢迎登录材料期刊网

材料期刊网

高级检索

采用有限元数值模拟与正交设计相结合的方法对热等静压态FGH96合金包覆挤压过程进行了数值模拟,系统分析了模具模角、工作带长度、入口圆角半径等模具关键结构参数对包覆层完整性、芯料挤压比和成形载荷的影响规律.确定了模具结构参数的最佳组合.结果表明:随着模角的减小、工作带长度的缩短和入口圆角半径的增大,有利于提高包覆层安全性,增大芯料挤压比.

参考文献

[1] MARQUEZ C;ESPERANCE G;KOUL A K .Prior Particle Boundary Precipitation in Ni-Base Superalloys[J].Powder Metallurgy,1989,25(04):301-308.
[2] KRUEGER D D;KISSINGER R D;MENZIES R G.Development and Introduction of a Damage Tolerant High Temperature Nickle-base Disk Alloy,Rene88 DT[J].The Superalloys,1992
[3] STOZ D S .Effect of a Supersolvus Heat Treatment on the Microstructure and Mechanical Properties of a Powder Metallurge Processed Nickel-Base superalloy[D].Florida:University of Florida,2004.
[4] SHARPE H J .Effect of Microstructure on High-Temperature Mechanical Behavior of Nickel-Base Superalloys for Turbine Disc Application[D].Atlanta GA:Georgia Institute of Technology,2007.
[5] 国为民,董建新,吴剑涛,张凤戈,陈淦生,陈生大.FGH96镍基粉末高温合金的组织和性能[J].钢铁研究学报,2005(01):59-63.
[6] 刘趁意,王淑云,东赟鹏,李惠曲,李付国,姜涛.FGH96合金挤压过程的数值模拟与试验研究[J].锻压装备与制造技术,2010(02):103-107.
[7] 王珏,董建新,张麦仓,郑磊,信继军.GH4169合金管材正挤压工艺优化的数值模拟[J].北京科技大学学报,2010(01):83-88.
[8] 王忠堂,王本贤,张士宏.GH1140管材热挤压工艺及组织性能研究[J].沈阳理工大学学报,2005(03):4-6,14.
[9] 周飞,李爱平,李大永,董俊.基于多重优化设计的铝型材挤压工作带模型[J].同济大学学报(自然科学版),2005(07):937-941.
[10] Bhavin V. Mehta;Ibrahim Al-Zkeri;Jay S. Gunasekera .3D flow analysis inside shear and streamlined extrusion dies for feeder plate design[J].Journal of Materials Processing Technology,2001(1/3):93-97.
[11] V. L. Kolmogorov;V. P. Fedotov;A. V. Gorshkov .Three-dimensional analysis of the stress-strain state in the process of plastic deformation of metals[J].Journal of Materials Processing Technology,1999(1/3):55-64.
[12] 刘玉红 .粉末高温合金等温成形模拟与控制[D].西安:西北工业大学,2004.
[13] 陈刚,陈忠富,陶俊林,牛伟,张青平,黄西成.45钢动态塑性本构参量与验证[J].爆炸与冲击,2005(05):451-456.
[14] 中国航空材料手册[M].北京:中国标准出版社,2002:323-368.
[15] 张吉,何祝斌,苑世剑.轴对称塑性变形区内一点流动方向的探索[J].机械工程学报,2007(12):74-77.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
文章评分
  • 您的评分:
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%