对汽车车身板用Al-1.5Si-1.2Mg-0.6Cu-0.3Mn铝合金冷轧薄板进行了固溶处理,研究了固溶温度、时间对第二相、晶粒及成形性能的影响规律.结果表明:在500～555℃之间进行固溶处理时,固溶温度升高,基体中残留的第二相数量逐渐减少,而再结晶晶粒尺寸形态变化不大;合金板材的强度和延伸率单调增大,,IE单调减小,n,r15变化不大.1.2 mm厚的冷轧合金薄板在540℃固溶处理时,保温时间需接近30 min才可使其具有良好的成形性,继续延长保温时间至180 min其成形性能变化不大.1.2 mm厚的A1-1.5Si-1.2Mg-0.6Cu-0.3Mn铝合金冷轧薄板合适的固溶处理温度为540℃,保温时间应接近30 min.常规T4状态的6xxx系铝合金薄板直接在汽车厂冲压成形后的烤漆涂装处理并不能起到提高车身构件强度的作用.
参考文献
| [1] | Miller W S;Zhuang L;Bottema J et al.Recent development in aluminium alloys for the automotive industry[J].Materials Science and Engineering A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2000,A280:37-49. |
| [2] | Hirth S M;Marshall G J;Court S A et al.Effects of Si on the aging behavior and formability of aluminium alloys based on AA6016[J].Materials Science and Engineering A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2001,A319-321:452-456. |
| [3] | Daniel Carle;Gordon Blount .The suitability of aluminium as an alternative material for car bodies[J].Materials & Design,1999(5):267-272. |
| [4] | Han JH.;Seok HK.;Chung YH.;Shin MC.;Lee JC. .Texture evolution of the strip cast 1050 Al alloy processed by continuous confined strip shearing and its formability evaluation[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2002(1/2):342-347. |
| [5] | Raabe D;Sachfleber M .Grain-scale mieromechanics of polycrystal surfaces during plastic straining[J].Acta Materialia,2003,51:1536-1560. |
| [6] | P. D. Wu;D. J. Lloyd .Analysis of surface roughening in AA6111 automotive sheet[J].Acta materialia,2004(7):1785-1798. |
| [7] | P. D. Wu;D. J. Lloyd;A. Bosland;H. Jin;S. R. MacEwen .Analysis of roping in AA6111 automotive sheet[J].Acta materialia,2003(7):1945-1957. |
| [8] | Baczynski G;Guzzo R;Ball M D et al.Development of roping in an aluminium automotive alloy AA6111[J].Acta Materialia,2000,48:3361-3376. |
| [9] | Humphreys F J .The nucleation of recrystallization at second phase particles in deformed aluminium[J].Acta metalhirgica,1977,25:1323-1344. |
| [10] | McQueen H J;Xia X;Cui Y et al.Solution and precipitation effects on hot workability of 6201 alloy[J].Materials Science and Engineering A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING,2001,A319-321:420-424. |
| [11] | Garrctt P R;Lin J;DeanTA .Aninvestigation of the effects of solution heat treatment on mechanical properties for AA 6xxx alloys:experimentation and modeling[J].International Journal of Plasticity,2005,21:1640-1657. |
| [12] | 刘宏,刘艳华,赵刚,刘春明,左良.Mn对Al-Mg-Si-Cu铝合金结晶相的影响[J].中国有色金属学报,2004(11):1906-1911. |
| [13] | LIU Hong,CHEN Yang,ZHAO Gang,LIU Chun-ming,ZUO Liang.Effect of pre-aging on precipitation behavior of Al- 1.29Mg- 1.22Si-0.68Cu-0.69Mn-0.3Fe-0.2Zn-0.1 Ti alloy[J].中国有色金属学会会刊（英文版）,2006(04):917-921. |
| [14] | 刘宏,赵刚,刘春明,左良.Mn对Al-Mg-Si-Cu铝合金车身板组织和性能的影响[J].东北大学学报（自然科学版）,2005(04):347-350. |
| [15] | 陈扬,赵刚,刘春明,左良.冷轧6111铝合金板材固溶处理后的再结晶织构[J].中国有色金属学报,2006(02):333-338. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%