Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

材料科学技术（英）, 2012, 28(1): 1-14.

Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

^1, , ^2, , ^3, , ^4, , ^5, , ^6, , ^7, , ^8, , ^9,

1.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

2.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

3.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

4.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

5.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

6.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

7.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

8.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

9.Department of Metallurgical and Materials Engineering, The University of Texas at E1 Paso, E1 Paso,TX 79968, USA W.M. Keck Center for 3D Innovation, The University of Texas at E1 Paso, E1 Paso, TX 79968, USA [Manuscript received October 27, 2011]

关键词：英文摘要 , 材料科学 , 优秀论文 , Lawrence , E

Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

Keywords： Selective laser melting , Electron beam melting , Additive manufacturing , Microstructures , Microstructural architecture

Lawrence E. Murr is Mr.J Mrs. Macintosh Murehison Professor and Chairman of the Department of Metallurgical and Materials Engineering and Ph.D. Program Director in the Materials Research Technology Institute at The University of Texas at El Paso. Dr. Murr received his B.Sc. in physical science from Albright College, and his B.S.E.E. in electronics, his M.S. in engineering mechanics, and his Ph.D. in solidstate science, all from the Pennsylvania State University. Dr. Murr has published 20 books, over 750 scientific and technical articles in a wide range of research areas in materials science and engineering, environmental science and engineering, manufacturing science and engineering (especially rapid prototype/layered manufacturing),

参考文献

[1]	L. E. MURR;S. M. GAYTAN;F. MEDINA;H. LOPEZ;E. MARTINEZ;B. I. MACHADO;D. H. HERNANDEZ;L. MARTINEZ;M. I. LOPEZ;R. B. WICKER;J. BRACKE .Next-generation biomedical implants using additive manufacturing of complex, cellular and functional mesh arrays[J].Philosophical transactions of the Royal Society. Mathematical, physical, and engineering sciences,2010(1917):1999-2032.
[2]	L.E. MURR;E. MARTINEZ;S.M. GAYTAN .Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2011(11):3491-3508.
[3]	L.E. Murr;E.V. Esquivel;S.A. Quinones .Microstructures and mechanical properties of electron beam-rapid manufactured Ti-6Al-4V biomedical prototypes compared to wrought Ti-6A1-4V[J].Materials Characterization,2009(2):96-105.
[4]	D.A. Ramirez;L.E. Murr;E. Martinez .Novel precipitate-microstructural architecture developed in the fabrication of solid copper components by additive manufacturing using electron beam melting[J].Acta materialia,2011(10):4088-4099.
[5]	L.E. MURR;E. MARTINEZ;S.M. GAYTAN .Microstructural Architecture, Microstructures, and Mechanical Properties for a Nickel-Base Superalloy Fabricated by Electron Beam Melting[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2011(11):3491-3508.
[6]	A. Strondl;R. Fischer;G. Frommeyer;A. Schneider .Investigations of MX and γ'/γ″ precipitates in the nickel-based superalloy 718 produced by electron beam melting[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2008(1/2):138-147.
[7]	M.Murayama;Y.Katayama .Microstructural evolution in a 17-4 PH stainless steel after aging at 400c[J].Metallurgical and materials transactions. A, physical metallurgy and materials science,1999(2):345-353.

上一张下一张

计量

下载量()
访问量()

作者相关

在本站搜索
在百度学术搜索
在万方数据库搜索
在CNKI搜索

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%

材料期刊网

Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

Metal Fabrication by Additive Manufacturing Using Laser and Electron Beam Melting Technologies

参考文献