通过测量挤压铸造过程的温度变化，采用基于非线性估算法的热传导有限元反算模型，求解不同挤压力下的界面传热系数(IHTC)。利用铸件中心模拟温度与测量温度验证模型的准确性；结合铸件表面和中心测温点温度变化讨论重力条件和挤压力条件下界面传热系数的变化规律，发现挤压力有效地增加了界面传热系数的峰值和稳定值。探讨挤压力对界面气隙的影响，对于ZL101A铝合金直接挤压铸造过程，50 MPa挤压力具有较好的挤压效果。
The temperature histories throughout squeeze casting process under different applied pressures were recorded. The interfacial heat transfer coefficients (IHTCs) were calculated by using an inverse method based on the nonlinear estimation method. To validate the inverse method, the comparison between measurement and simulation temperatures in the center of castings was taken. IHTCs under gravity and pressure condition, respectively, were discussed with the surface and centre temperature histories of castings to obtain a general rule. The results show that the peak and stable values of IHTCs increase obviously with increasing the applied pressure. Additionally, the effect of applied pressure to interface air gap was discussed, and 50 MPa applied pressure performs sufficiently to direct squeeze casting process of ZL101A aluminum alloy.
参考文献
| [1] | GRIFFITHS W D .A model of the interfacial heat-transfer coefficient during unidirectional solidification of an aluminum alloy[J].Metallurgical and Materials Transactions B:Process Metallurgy and Materials Processing Science,2000,31(02):285-295. |
| [2] | 郭志鹏,熊守美,曺尚铉,崔正吉.热传导反算模型的建立及其在求解界面热流过程中的应用[J].金属学报,2007(06):607-611. |
| [3] | SANTOS C A;SIQUEIRA C A;GARCIA A;QUARESMA J M SPIM J A .Metal-mold heat transfer coefficients during horizontal and vertical unsteady-state solidification of Al-Cu and Sn-Pb alloys[J].INVERSE PROBLEMS IN SCIENCE AND ENGINEERING,2004,12(03):279-296. |
| [4] | A. HAMASAIID;M.S. DARGUSCH;C.J. DAVIDSON .Effect of Mold Coating Materials and Thickness on Heat Transfer in Permanent Mold Casting of Aluminum Alloys[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2007(6):1303-1316. |
| [5] | C.A. Santos;J.M.V. Quaresma;A. Garcia .Determination of transient interfacial heat transfer coefficients in chill mold castings[J].Journal of Alloys and Compounds: An Interdisciplinary Journal of Materials Science and Solid-state Chemistry and Physics,2001(1/2):174-186. |
| [6] | IVALDO L. FERREIRA;CARLOS A. SANTOS;VAUGHAN R. VOLLER .Analytical, Numerical, and Experimental Analysis of Inverse Macrosegregation during Upward Unidirectional Solidification of Al-Cu Alloys[J].Metallurgical and Materials Transactions, B. Process metallurgy and materials processing science,2004(2):285-297. |
| [7] | 刘源,郭景杰,贾均,李言祥,苏彦庆,丁宏升.Equivalent heat transfer coefficient at casting/Cu mould interface and temperature field simulation[J].中国有色金属学会会刊(英文版),2003(05):1119-1123. |
| [8] | ZHOU Ji-ming,QI Le-hua,CHEN Guo-ding.New inverse method for identification of constitutive parameters[J].中国有色金属学会会刊（英文版）,2006(01):148-152. |
| [9] | Z. W. Chen .Skin solidification during high pressure die casting of Al-11Si-2Cu-1Fe alloy[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2003(1/2):145-153. |
| [10] | SAHIN H M;KOCATEPE K;KAYIKCI R;AKARA N .Determination of unidirectional heat transfer coefficient during unsteady-state solidification at metal casting-chill interface[J].Energy Conversion & Management,2006,47(01):19-34. |
| [11] | Spinelli JE;Ferreira IL;Garcia A .Evaluation of heat transfer coefficients during upward and downward transient directional solidification of Al-Si alloys[J].Structural and multidisciplinary optimization,2006(3):241-248. |
| [12] | J. O. Aweda;M. B. Adeyemi .Experimental determination of heat transfer coefficients during squeeze casting of aluminium[J].Journal of Materials Processing Technology,2009(3):1477-1483. |
| [13] | J. O. Aweda;M. B. Adeyemi .Determination of temperature distribution in squeeze cast aluminium using the semi-empirical equations' method[J].Journal of Materials Processing Technology,2009(17):5751-5759. |
| [14] | A. Fardi Ilkhchy;M. Jabbari;P. Davami .Effect of pressure on heat transfer coefficient at the metal/mold interface of A356 aluminum alloy[J].International Communications in Heat and Mass Transfer: A Rapid Communications Journal,2012(5):705-712. |
| [15] | BECK J V.Inverse heat conduction:Illposed Problems[M].James Beck,1985 |
| [16] | Zhizhong Sun;Henry Hu;Xiaoping Niu .Determination of heat transfer coefficients by extrapolation and numerical inverse methods in squeeze casting of magnesium alloy AM60[J].Journal of Materials Processing Technology,2011(8):1432-1440. |
| [17] | Noe Cheung;Ivaldo L. Ferreira;Moises M. Pariona;Jose M.V. Quaresma;Amauri Garcia .Melt characteristics and solidification growth direction with respect to gravity affecting the interfacial heat transfer coefficient of chill castings[J].Materials & design,2009(9):3525-3536. |
| [18] | SUI Da-shan,CUI Zhen-shan.Regularized determination of interfacial heat transfer coefficient during ZL102 solidification process[J].中国有色金属学会会刊（英文版）,2008(02):399-404. |
| [19] | 隋大山,CUI Zhen-shan.铸铝件凝固过程三维瞬态温度场的数值模拟[J].中国有色金属学报,2008(07):1311-1316. |
| [20] | DOUR G;DARGUSCH M;DAVIDSON C;NEF A .Development of a non-intrusive heat transfer coefficient gauge and its application to high pressure die casting:Effect of the process parameters[J].Journal of Materials Processing Technology,2005,169(02):223-233. |
| [21] | Chunsheng Li;Brian G. Thomas .Thermomechanical Finite-Element Model of Shell Behavior in Continuous Casting of Steel[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,2004(6):1151-1172. |
| [22] | MOAVENI S;王崧;刘丽娟;董春敏,.有限元分析-ANSYS 理论与应用[M].北京:电子工业出版社,2008:295-322. |
| [23] | 朱维,韩志强,柳百成.挤压铸造凝固过程热-力耦合模拟Ⅱ.模拟计算及实验验证[J].金属学报,2009(03):363-368. |
| [24] | JORSTAD J L.High integrity die casting process variations[A].,2003:137-148. |
| [25] | Griffiths, WD;Kawai, K .The effect of increased pressure on interfacial heat transfer in the aluminium gravity die casting process[J].Journal of Materials Science,2010(9):2330-2339. |
| [26] | 张克武,赵海东,欧阳晓贤,张卫文,李元元.不同挤压力下凝固的Al-Si-Cu-T4的组织与性能[J].中国有色金属学报,2009(04):625-632. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%