Dry sliding wear tests of a Cr-Mo-V cast hot-forging die steel was carried out within a load range of 50--300 N at 400℃ by a pin-on-disc high temperature wear machine. The effect of heat treatment process on wear resistance was systematically studied in order to select heat treatment processes of the steel with high wear resistance. The morphology, structure and composition were analyzed using scanning electron microscopy （SEM）, X-ray diffraction （XRD） and energy dispersive spectroscopy （EDS） ; wear mechanism was also discussed. Tribo-oxide layer was found to form on worn surfaces to reduce wear under low loads, but appear inside the matrix to increase wear under high loads. The tribo-oxides were mainly consisted of Fe3O4 and Fe2O3, FeO only appeared under a high load. Oxidative mild wear, transition of mild-severe wear in oxidative wear and extrusive wear took turns to operate with increasing the load. The wear resistance strongly depended on the selection of heat treatment processes or microstructures. It was found that bainite presented a better wear resistance than martensite plus bainite duplex structure, martensite structure was of the poorest wear resistance. The wear resistance increased with increasing austenizing temperature in the range of 920 to 1 120 ℃, then decreased at up to 1 220 ℃. As for tempering temperature and microstructure, the wear resistance increased in following order： 700℃ （tempered sorbite）, 200 ℃ （tempered martensite）, 440 to 650 ℃ （tempered troostite）. An appropriate combination of hardness, toughness, microstructural thermal stability was re- quired for a good wear resistance in high-temperature wear. The optimized heat treatment process was suggested for the cast hot-forging steel to be austenized at 1020 to 1 120 ℃, quenched in oil, then tempered at 440 to 650℃ for 2 h.
参考文献
| [1] | Castro G;Fernandez-Vicente A;Cid J .Influence of the Nitriding Time in the Wear Behaviou of an AISI H13 Steel During a Crankshaft Forging Process[J].Wear,2007,263:1375. |
| [2] | Beeley P R;Blackmore A .Production and Evaluation of Cast- to-Form Forging Dies in a Special Cast Steel[J].Metals and Technology,1981,17-18:268. |
| [3] | Beeley P R .Cast Steels for Tools and Dies:a Review[J].British Foundryman,1986,79:441. |
| [4] | Jiang Q C;Fang J R;Wang S Q et al.Selection of Tempering Technology of New Cast Die Steel for Hot Forging[J].Transactions of Metal Heat Treatment,2000,25:34. |
| [5] | O. Barrau;C. Boher;R. Gras;F. Rezai-Aria .Analysis of the friction and wear behaviour of hot work tool steel for forging[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2003(7/12):1444-1454. |
| [6] | Luong L H S;Heijkoop T .The Influence of Scale on Friction in Hot MetalWorking[J].Wear,1981,71:93. |
| [7] | Zhu Z Y .Data of Hot Working Die Steels[J].Mechanical Engineering Materials,2001,25:40. |
| [8] | CUI Xiang-hong .High-Temperature Wear of a New-Developed Hot-Forging Cast Die Steel[D].长春:吉林大学,2006. |
| [9] | CUI Xiang-hong,SHAN Jun,YANG Zi-run,WEI Min-xian,WANG Shu-qi,DONG Chuang.Alloying Design for High Wear-Resistant Cast Hot-Forging Die Steels[J].钢铁研究学报（英文版）,2008(04):67-72. |
| [10] | Cui X H;Wang S Q;Jiang Q C et al.Research on Thermal Wear of Cast Hot Forging Die Steel Modified by Rare Earths[J].Journal of Rare Earths,2007,25:88. |
| [11] | Wei M X;Wang F;Wang S Q et al.Comparative Research on the Elevated-Temperature Wear Resistance of a Cast Hot- Working Die Steel[J].Materials & Design,2009,30:3608. |
| [12] | Quinn T F J;Sullivan J L;Rowson D M .Developments in the Oxidational Theory of Mild Wear[J].Tribology International,1980,13:153. |
| [13] | H. So;D. S. Yu;C. Y. Chuang .Formation and wear mechanism of tribo-oxides and the regime of oxidational wear of steel[J].Wear: an International Journal on the Science and Technology of Friction, Lubrication and Wear,2002(9/10):1004-1015. |
| [14] | Wilson J E;Stott F H;Wood G C .The Development of Wear Protective Oxides and Their Influence on Sliding Friction[J].Proceedings of the Royal Society,1980,369A:557. |
| [15] | Quinn T F J .Oxidational Wear Modelling Part III:the Effects of Speed and Elevated Temperatures[J].Wear,1998,216:262. |
| [16] | Suh N P .The Delamination Theory of Wear[J].Wear,1973,25:111. |
| [17] | Wang S Q;Wei M X;Wang F et al.Transition of Elevated- Temperature Wear Mechanisms and the Oxidative Delamination Wear in Hot-Working Die Steels[J].Tribology International,2010,43:577. |
| [18] | Wang S Q;Wei M X;Zhao Y T .Effects of the Tribo-Oxide and Matrix on Dry Sliding Wear Characteristics and Mecha- nisms of a Cast Steel[J].Wear,2010,269:424. |
| [19] | QI Zheng-feng.Metal Heat-Treatment Principles[M].Beijing:Machinery Industry Press of China,1987:159. |
| [20] | Jahanmir S;Suh N P .Mechanics of Subsurface Void Nucleation in Delamination Wear[J].Wear,1977,44:17. |
| [21] | S. Q. Wang;M. X. Wei;F. Wang;X. H. Cui;C. Dong .Transition of Mild Wear to Severe Wear in Oxidative Wear of H21 Steel[J].Tribology letters,2008(2):67-72. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%