以工业碳化硼粉末为原料、采用Si3N4磨球磨损法引入Si3N4烧结助剂,采用水基流延成型和热压烧结方法制备了碳化硼陶瓷.研究了氧含量、分散剂、pH值等因素对B4C陶瓷浆料分散性能的影响,采用XRD、SEM等对碳化硼陶瓷的物相、显微结构和第二相分布进行了表征,并测试了样品的维氏硬度、断裂韧性、抗弯强度和弹性模量.结果表明:经醇洗后的碳化硼粉末中氧化硼含量降低,有利于B4C陶瓷浆料的分散稳定.采用球磨磨损引入了Si3N4粉,在B4C基体中通过原位反应形成第二相SiC和BN,SiC和BN第二相颗粒在B4C基体中弥散分布均匀.在2100 ℃热压烧结样品的维氏硬度、抗弯强度、断裂韧性和弹性模量分别达到30.2 GPa、596.5 MPa、3.36 MPa·m1/2和362.3 GPa.
参考文献
| [1] | Thevenot F .A Review on Boron Carbide[J].Key Engineering Materials,1991,56-57:59-88. |
| [2] | Hirao K.;Brito ME.;Kanzaki S.;Ohashi M. .PROCESSING STRATEGY FOR PRODUCING HIGHLY ANISOTROPIC SILICON NITRIDE[J].Journal of the American Ceramic Society,1995(6):1687-1690. |
| [3] | Cui X;Ouyang S;Yu Z et al.A Study on Green Tapes for LOM with Water-based Tape Casting processing[J].Materials Letters,2003,57:1300-1304. |
| [4] | Ridway R R .Boron Carbide:a New Crystalline Abrasive and Wear-resisting Product[J].Trans.Am.Eletrochem.Soc,1934,66:117-133. |
| [5] | Das A;Madras G;Dasgupta N et al.Binder Removal Studies in Ceramic Thick Shapes Made by Laminated Object Manufacturing[J].Journal of the European Ceramic Society,2003,23:1013-1017. |
| [6] | 宁叔帆,李鸿岩,陈维,刘斌,陈寿田.表面氧化物含量对SiC浆料黏度影响的研究[J].西安交通大学学报,2005(06):641-645. |
| [7] | Williams P D;Hawn D D .Aqueous Dispersion and Sip Casting of Boron Carbide Powder:Effect of pH and Oxygen Content[J].Journal of the American Ceramic Society,1991,74(07):1614-1618. |
| [8] | Jingxian Zhang;Feng Ye;Dongliang Jiang .Preparation of bulk Si_3N_4 from tape casting and lamination[J].CERAMICS INTERNATIONAL,2006(3):277-282. |
| [9] | Pyzik A J;Aksay I A .Microdesigning of B4C-Al Cermets[J].Processing of Ceramics and Metal Matrix Composites Pergamon,1989,26:269-280. |
| [10] | Zhang G J;Beppu Y .Reaction Mechanism and Microstruction Development of Strain Tolerant in Situ SiC-BN Composites[J].Acta.Mater,2001,49(01):77-82. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%