师仲然
,
Fahlstr(o)m K
,
Hutchinson B
,
Komenda J
,
Lindh-Ulmgren E
,
Martin D
,
BeladiH
钢铁钒钛
doi:10.7513/j.issn.1004-7638.2015.03.021
研究了结构钢单道次焊接接头,尤其是靠近融合线位置的粗晶热影响区(CGHAZ)的组织和力学性能.通常,这个区域的韧性比母材和焊缝金属的韧性要低很多,所以CGHAZ是最容易发生断裂的薄弱位置.重点关注钒微合金化钢板,并且与相同强度级别的铌微合金化钢板进行对比.为了充分利用钒的强化效果,有必要将氮含量提高至0.01％;为优化钢的性能,必须考虑钒与氮的配合.
关键词:
钢
,
钒
,
焊接
,
热影响区(HAZ)
,
韧性
,
组织
Ying LI
材料科学技术（英文）
Oxide materials NaCo2O4 and (Na1-yMy)1.6Co2O4 (M=K, 0.05≤y≤0.35; M=Ca, Sr, 0.10≤y≤0.40) were prepared by a sol-gel method. Experimental results indicated that the Seebeck coefficient and the Power-factor of Na Co2O4 were improved by doping Ca and Sr but not by K. The Power-factor of NaCo2O4 is in its maximum, 1.68×10-4 W•m-1•K-2 and 11% bigger than that of the original one when the dopant fraction of Ca was 0.1. Doping Sr makes NaCo2O4 have the biggest Power-factor, 1.68×10-4 W•m-1•K-2 that is 50% bigger than the non-doping oxide. The experimental results indicate that suitable dopants and addition amounts could improve the thermoelectric properties of NaCo2O4 greatly.
关键词:
Thermoelectric materials
,
materials
,
Electric
,
proper
李志友
,
黄伯云
,
汤春峰
,
刘志坚
,
曲选辉
功能材料
用柠檬酸盐溶胶-凝胶工艺制取了三种β-MxV2O5氧化物Li0.3V2O5、Na0.33 V2O5和K0.25V2O5;TG和DTA试验显示干凝胶焙烧过程中出现两个吸热峰,中间有一个放热峰;XRD分析表明高温处理时Li0.3 V2O5可氧化成LiV3O8和V2O5,而Na0.33V2O5和K0.25有较好的化学稳定性;模拟Li-B合金/LiCl-KCl/β-MxV2O5(或α-V2O5)热电池500℃放电试验表明β相阴极放电较α相平稳,但初始电压峰值略有降低,β-Li0.3V2O5相因具有较α-V2O5相更通畅的Li+快速扩散通道,且通道内没有Na+或K+大离子对Li+扩散的阻碍,放电最为平稳,有效比容量最高.
关键词:
溶胶-凝胶工艺
,
β相钒青石
,
热电池
,
阴极
刘勤
,
夏锄
,
刘晓东
金属学报
在170,190,210,230,250℃的温度下,采用3.7×10~2,7.4×10~2和1.1×10~(-1)min(-1)的应变速率(平均)对Zn-5%Al共晶合金的m-C-δ(或m-k-δ)关系曲线(简称m-δ关系曲线)进行了测定.所有的曲线均随应变的δ增加而快速上升.俟达到某一定的应变量(极限应变量δ1)后。开始缓慢下降并保持平稳直至断裂.Zn-5%A1共晶合金的m-δ关系曲线不存在k_(?)=k_I(k_(I 1),k_(I 2),k_(I 3),……)=k_F(或C_0=C_I(C_(I 1),C_(I 2),C_(I 3),……)=C_F=1)的简单情况.可应用m-δ方程式[4,5]对曲线上各点C值(包括所有的C_I和C_F值)进行计算.C值随δ值的增加成近似的直线上升.直线的斜率在极限应变(δ1)处突然减小.
关键词:
阎峰云
,
刘兰
,
夏心俊
,
何玲
功能材料
doi:10.3969/j.issn.1001-9731.2017.02.032
采用化学共沉淀法制备出SrAl2O4∶Eu3+红色荧光粉,尝试向粉体中添加辅助激活剂(Li+、Na+、K+),改变粉体中基质元素相对比例,并对粉体进行XRD、荧光光谱分析.结果表明,样品中加入相同摩尔的Li+、Na+、K+辅助激活剂,掺入Li+的粉体发光强度最好.改变Li+的掺入量,当Li+的量为0.04 mol时,粉体发光强度最好.改变粉体中基质Sr2+的含量,当掺入Ba2+时,荧光粉发射峰出现"蓝移"现象;当掺入Ca2+时,荧光粉发射峰出现"红移"现象.
关键词:
共沉淀
,
红色荧光粉
,
辅助激活剂
,
基质
胡标
,
尹明
,
王庆平
,
闵凡飞
,
杜勇
兵器材料科学与工程
基于文献报道的实验数据,采用相图计算(CALPHAD:CALculation of PHAse Diagrams)方法对V-M(M=Li,Na,K,Sc,Ag)5个二元系进行相图热力学研究.通过热力学优化计算获得了一套描述液相、(V)、(Li)、(Na)、(K)、(αSc)、(βSc)和(Ag)相的热力学参数.V-Li、V-Na和V-K体系中的气相视为由组元V、Li、Li2、Na、Na2、K和K2混合的理想气体.与实验相图数据对比表明,获得的热力学参数能够准确地描述实验相平衡数据.
关键词:
V-M(M=Li,Na,K,Sc,Ag)
,
CALPHAD方法
,
相图
,
热力学模型
Materials Letters
Secondary M,C precipitation was investigated in K40S cobalt-base alloy after 100 h aging at 950 degreesC. The results showed that it was closely related to the tungsten-rich zones inherited from the as-cast condition and the degeneration of the primary M7C3 carbide. A direct element reaction, 6M + C --> M6C, in which C comes from the decomposition of the M7C3 carbides, is suggested as the mechanism of secondary M6C precipitation in K40S alloy. (C) 2001 Elsevier Science B.V. All rights reserved.
关键词:
M6C precipitation;aging;M7C3 carbide;superalloy
Journal of Alloys and Compounds
Magnetization measurements on lead- or tin-doped YBa2Cu3O7 have been performed at 4.2 K in magnetic fields up to 29 T. The critical current densities are deduced from the irreversible magnetization and the pinning forces are evaluated. The effect of both lead and tin doping on the critical current density is quite appreciable. In particular, the critical current density of the sample doped with lead is more than twice that of the undoped sample. This effect is thought to be associated with the enhancement of the intergranular coupling of grains through the formation of BaPbO3 phase at the interface of the 123 superconducting phase. The relationship between the critical current density and a micrograph of the tin-doped sample is also discussed.
关键词:
transport critical current;y1ba2cu3ox
