G.F. Zhou
,
M. B. Wen
,
P. H. Li and X. L. He 1) National Enterprise Technology Center
,
Wuhan Iron & Steel Group Co.
,
Wuhan 430080
,
China 2) University of Science and Technology Beijing
,
Beijing 100083
,
China
金属学报(英文版)
The stress relaxation curves of Ultra-Low Carbon Bainitic(ULCB) steels with different Cu and B contents were measured by using Gleeble-1500 dynamic thermal-mechanical simulator. The results show that Cu and B added can accelerate the strain-induced precipitation reaction, and the effect of Cu and B is even more obvious with Cu and B combined addition or Cu content increased. The TEM analysis of precipitate engendered at the temperature of 850℃ C indicate that Nb(C,N) precipitate nucleates dominantly on the dislocation line, and grows with holding time extended while the precipitate particle size increases from 5 nm to 17 nm.
关键词:
stress relaxation
,
null
,
null
沈基显
,
黄剑锋
,
曹丽云
,
曾燮榕
,
熊信柏
稀有金属材料与工程
以羟基磷灰石-壳聚糖(HA-CS)为基体,玻璃纤维G(f)为增强相,采用原位杂化法制备短玻璃纤维增强HA-CS基生物复合材料.研究交联剂、羟基磷灰石含量和玻璃纤维含量对复合材料性能的影响.采用红外吸收光谱、扫描电子显微镜和万能材料试验机对材料的结构和性能进行表征.结果表明:原位杂化法能制备性能较好的复合材料;用戊二醛交联改性复合材料可以明显增加其韧性和弯曲强度,使复合材料抗弯曲强度提高16%;当CS/HA=10/1(质量比)和玻璃纤维含量为1.5%时复合材料抗折强度达到极大值84.47 MPa;随玻璃纤维含量的增加,复合材料的断裂面由平整向多层断裂变化,材料的韧性有所提高.
关键词:
G(f)/HA-CS复合材料
,
玻璃纤维
,
交联剂
,
弯曲强度
Physica B-Condensed Matter
In this paper, a simple and uniform expression for calculating the anisotropy of the g factor (characterized by DELTAg = g(perpendicular-to) - g(parallel-to)) for 3d(n) ions in the tetragonal phase of the perovskite structure from the spin-lattice coupling coefficients F11 and F12 in the cubic phase has been proposed by introducing a release factor k. From this expression, the values of DELTAg for Ni2+(3d8) and Ni3+ (3d7) ions in the tetragonal phase of a SrTiO3 Crystal are studied. It is found that for SrTiO3:Ni2+, the observed isotropy of the g factor (DELTAg = 0) is due to the too small value of (F11 - F12) and for SrTiO3: Ni3+, the contribution to DELTAg from the elongation of the octahedron around the Ni3+ ion is important in the case of T near the transition temperature T(c).
关键词:
lattice coupling-coefficients;cubic symmetry;fij
冶金分析
提出了离子色谱法检测电镀液中F-和Cl-的方法.根据高沸点酸置换低沸点酸,用硫酸作为蒸馏剂,在一定的温度下,将F-和Cl-一起蒸馏出进行分离和富集,消除了电镀液中大量共存离子的干扰和对色谱柱的污染.使用IonPacASl4A作为色谱柱,在合适的色谱条件下,F-和Cl-的色谱峰能很好地分离,其检出限分别为0.84 μg/L和0.37 μg/L,相对标准偏差F-小于7.3%,Cl-小于4.2%(n=10),加标回收率F-在91%~107%、Cl-在95%~105%之间(n=10),电镀液中共存离子对F-和Cl-的测定无干扰.方法用于电镀液中F-和Cl-的同时测定,具有很好的可行性和实用性.
关键词:
F-
,
Cl-
,
离子色谱
,
蒸馏法
,
电镀液
阳建红
,
董进辉
,
李海斌
,
石强
,
郭明映
复合材料学报
在60℃、80℃相对湿度90%环境条件下对F-12纤维进行了湿热老化实验,研究了长时间老化时纤维吸湿规律.通过ATR-FTIR光谱分析了湿热老化后水对F-12纤维化学结构的影响以及水在纤维中可能存在的方式,探讨了吸湿机制,实验研究了纤维单丝拉伸强度的变化,并采用SEM观察了纤维表面及拉伸断口形貌.结果表明:F-12纤维长时间的吸湿属于2阶段吸湿,吸湿初期符合Fick第二定律,后期偏离,吸湿2500 h后仍没达到平衡;水分子对F-12纤维的化学结构没有造成明显的破坏,老化2500 h后F-12纤维表面变得粗糙,出现了一些沟槽,老化后期断口呈现出脆性与原纤化复合的特征;拉伸断裂强度并非持续减小,而是在起伏波动中减小.
关键词:
F-12纤维
,
吸湿规律
,
ATR-FTIR
,
SEM
,
吸湿机制
,
拉伸强度