LI Hai-feng
,
LUO Zhi-guo
,
ZOU Zong-shu
,
SUN Jun-jie
,
HAN Li-hao
,
DI Zhan-xia
钢铁研究学报(英文版)
COREX process is one of the earliest industrialized smelting reduction ironmaking technology. A numerical simulation model based on discrete element method (DEM) has been developed to analyze the burden distribution in the melter gasifier of COREX process. The DEM considering the collisions between particles can directly reproduce the charging process. The burden trajectory, the location and the burden surface profile are analyzed in melter gasifier with a mixing charging of coal and direct reduction iron (DRI) at the same time. Considering the porosity of packed bed has an important effect on the gas flow distribution of melter gasifier, a method to calculate porosity has been proposed. The distribution of DRI and coal and the porosity in the radial direction are given under different charging patterns, which is necessary to judge the gas flow distribution and provide base data for further researching the melter gasifier for the next work in the future. The research results can be used to guide the operation of adjusting charging and provide important basis for optimizing the charging patterns in order to obtain the reasonable gas distribution.
关键词:
COREX melter gasifier
,
burden distribution
,
gas distribution
,
discrete element method
中国腐蚀与防护学报
N。1Atmospheric Corrosivlty for Steels………………………………………………… .LIANG Caideng HO[I i。-tat（6）Caustic Stress Corrosion Cr。king of Alloy 800 Part 2.The Effect of Thiosul执e……………………………………… KONG De-sheng YANG Wu ZHAO Guo-zheng HUANG De.ltL。ZHANG Yu。。he CHEN She。g-bac（13）SERS slid E16CttOCh6iniC81 Stlldy Of Illhibit1Oli M6ch＆tllsth Of ThlollY68 Oil ITOll ID H....
关键词:
杨立新
,
巴黎明
,
李星
工程热物理学报
本文应用MUSIG模型[1]和均一直径模型对某溶液堆台架模型堆芯内气液流动传热进行了数值模拟.在MUSIG模型中堆芯内离散相气泡被分为5组不同直径的气泡,用于分析堆芯内气泡的流动变化和大小分布,采用Luo and Svendsen[2]和Prince and Blanch[3]模型描述不同直径气泡组间的破裂和聚合.在均一直径模型中,堆芯内的气体被考虑为同一直径的组分,并且不考虑其破裂与聚合现象.计算得到采用两个模型的模拟结果并且对其进行了对比研究.结果显示应用MUSIG模型的计算结果与台架实验结果吻合更好.
关键词:
MUSIG
,
均一直径
,
两相流
,
溶液堆
李凤娟
,
吕国光
金属世界
doi:10.3969/j.issn.1000-6826.2014.04.14
通过对烧结配料所需原料及对冷烧结矿成品检验采制样方法的分析，找出影响检验结果真实性的因素，采取有效的改进措施，使本钢原料厂一次配料、本钢炼铁厂265 m2烧结二次配料及265 m2烧结系统各项稳定率有了很大的提高，烧结矿实物质量和各项技术质量指标有了很大的进步，保证了高炉的稳定顺行。
提高本钢265 m2冷烧结矿及原料检验代表性的实践
Practice of Improving the 265 m2 Cold Sinter and Raw Material Inspection Representative
供稿|
李凤娟,吕国光/
LI Feng-juan, LV Guo-guang
DOI：10.3969/j.issn.1000-6826.2014.04.14
导读内容
本钢炼铁厂265 m2烧结机生产所需要的含铁原料比较复杂，一次配料料种较多，且烧结含铁原料是由本钢原料厂二车间供料，原料质量的不稳定，会影响烧结矿质量的提高和新一号高炉的强化及高炉技术指标的改善。本钢质量管理中心驻冷烧检查站加强了对烧结配料所需原料及对冷烧结矿成品检验采制样代表性的研究，采取了一些改进措施，达到了良好的效果。含铁料成分稳定率、烧结矿各项质量和技术指标在稳步地提高。下面，对本钢质量管理中心驻冷烧检查站就提高采样及检验过程的准确性所采取的措施和办法进行说明。
烧结矿采样是半自动采样，每两小时采样一次，作为一个批次，来代表整个2h烧结矿的成份。
关键词:
