徐菊良
,
邓博
,
孙涛
,
李劲
,
蒋益明
金属学报
doi:10.3724/SP.J.1037.2009.00598
利用Thermo-Calc软件并结合金相显微镜,定性研究了2205双相不锈钢在800℃下敏化不同时间后的微观组织演变过程.通过研究扫描速率、介质成分、介质温度和试样表面状态优化了双环电化学动电位再活化法(DL-EPR),并用该优化方法研究了2205双相不锈钢晶间腐蚀敏感性.结果表明:DL-EPR法能定量评价σ相对2205双相不锈钢晶间腐蚀敏感性的影响,随敏化时间延长,σ相含量增多,晶jian 腐蚀敏感性也随之增加.腐蚀形貌的观测验证了这一规律,
关键词:
2205双相不锈钢
,
DL-EPR
,
晶间腐蚀敏感性
,
σ相
Journal of Physics-Condensed Matter
This research purposes to investigate the atomic and electronic structures of the Al/TiC(001) interface with lattice misfit using the ab initio pseudopotential approach. A detailed analysis of the relaxed atomic structure reveals that the atoms over the initial unfavourable sites relax to the favourable sites along the lateral plane. The properties of the semicoherent interface can be taken as averages over the different coherent sites. In addition, the interface atoms in relatively favourable regions are dragged near to the interface, while those in unfavourable regions are pushed away from the interface. Therefore, a large war-ping near the interface is made perpendicular to the lateral plane. The calculated adhesions explain the different wetting results from the viewpoint of structural transition. The subsequent analysis of electronic properties demonstrates that adhesions dominate mainly via the strong Al-C covalent bond.
关键词:
first-principles;1st principles;adhesion;surfaces;misfit;1st-principles;wettability;al
X. Q. Yang
,
L. X. Huo
,
Y. F. Zhang and J. X. Yan (School of Material Science and Engineering
,
Tianjin University
,
Tianjin 300072
,
China)
金属学报(英文版)
The buckling formation and influence factors during welding thin - plated structures were investigated based on finite element methods, An engineering treatment method for prdicating the buckling distor- tion was proposed in here. It was used the equivalent applied thermal - load to simulate the welding residual stress,therefore the calculation of complex welding distoriton can be transformed into 3D elas- tic structural applied- load analyses, which can reduce the quantities of calculating works effectively. The validation of the method was verified by comparison of the numerical simulation and experimental results. The simulation of buckling distorition for side - walled structrues of paseenger train was per- formed and the calculation was in agreement with measuring results in general. It was shown that the main factors for producing the buckling were the intermittent fillet and ping the during welding the stiffened beams and columns to the panel.The existence of the free edge of panels would reduce the crit- ical buckling stress and enlarge the deflection obviously,but the continuous weld in closed frames didn' t degrade the buckling situation.
关键词:
welding buckling distortion
,
null
,
null
周镇
,
艾育华
,
孔文俊
工程热物理学报
本文利用双腔泄压式定压燃烧弹,研究了高压下典型IGCC合成气的层流火焰传播特性,得到了不同压力(0.1～1 MPa)和不同当量比下(0.6～3.0)合成气的层流火焰传播速度和Markstein长度.实验结果表明,层流火焰传播速度随当量比先增加后减少,随压力的增加而减小.Davis和Sun机理能较好地预测高压下合成气层流火焰的传播速度.Markstein长度随当量比的增加而增加,随压力的增加而减小.
关键词:
合成气
,
球形火焰
,
层流火焰传播速度
,
Markstein长度
程杰锋
,
唐广波
,
刘正东
钢铁研究学报
选取了现有典型的C-Mn钢相变过程的物理冶金模型,包括5组孕育期模型、7组相变动力学方程模型、5组相变后铁素体晶粒尺寸模型.利用自行开发的组织性能预报系统软件模拟计算了在3组实际冷却工艺条件下各模型的奥氏体转变过程,并对各模型进行了评价.结果表明,对于所设定的成分和工艺条件,适用性较好的孕育期模型是Kwon所提出的模型;适用性较好的动力学方程模型是Liu、Donnay和Sun所提出的模型;适用性较好的铁索体晶粒尺寸模型是Hodgson所提出的模型.
关键词:
孕育期
,
相变
,
适用性分析
朱亮
,
肖毅
复合材料学报
为满足在工程应用中对建立拉压性能不同纤维增强复合材料的非线性本构理论的需要,考虑静水压影响的Drucker-Prager屈服准则与各向异性的Hill屈服准则相结合,提出了广义Hill屈服准则,并推广到Sun-Chen的单参数塑性模型中,建立了考虑拉压异性复合材料的非线性统一本构方程.实验验证结果表明,运用本文中所建立的本构模型能够很好地描述碳纤维/环氧(IM600/Q133)复合材料在偏轴拉伸和压缩载荷作用下的非线性响应.
关键词:
单向复合材料
,
非线性响应
,
不同屈服强度
,
本构方程
,
偏轴拉伸-压缩载荷
