XU Feng-yun
,
WANG Yong-wei
钢铁研究学报(英文版)
CCT curves of Mn-Si steels with different Mn content or carbon content were tested and on this basis, water cooled baintic steels with non-expensive alloy element were developed. The results show that transformation of bainite can be separated from that of ferrite when Mn content approach certain content; relative length of incubation time of ferrite and bainite transformation can be controlled by changing carbon content in Mn-Si; granular bainite was obtained when Ф300mm bar cooled by water, mix structure of fine widmanstatten ferrite, granular bainite and martensite was obtained as plate of 40mm thickness cooled by water; water cooled baintic steels developed with non-expensive alloy shows good combination of strength and toughness and tensile strength, yield strength and toughness (AKU -20 oC ) of Ф300m bar after water cooled is higher than 850MPa, 620MPa, 65 J respectively, and tensile strength, yield strength and toughness (AKU -20 oC ) of plate of 40mm thickness after water cooled is higher than 1000 MPa, 800MPa, 50 J respectively
关键词:
Bainitic steels;water-cooling;granular bainite;CCT curves;Mn-Si steel
Journal of Materials Research
The morphology of the dark and bright regions observed by transmission electron microscopy for the Zr(64.13)Cu(15.75)Ni(10.12)Al(10) bulk metallic glass strongly depends on the ion beam parameters used for ion milling. This indicates that the ion beam could introduce surface fluctuation to metallic glasses during ion milling.
关键词:
room-temperature
X.B. Tian
,
X.F. Wang
,
A.G. Liu
,
L.P. Wang
,
S. Y. Wang
,
B. Y. Tang and P. K. Chu 1)Advanced Welding Production & Technology National Key Laboratory
,
Harbin Institute of Technology
,
Harbin 150001
,
China 2)Department of Physics & Materials Science
,
City University of Hong Kong
,
China
金属学报(英文版)
The research on plasma immersion ion implantation has been conducted for a little over ten years. Much is needed to investigate including processing technlogy, plasma sheath dynamics, interaction of plasma and surface, etc. Of the processing methods elavated temperature technique is usually used in PIII to produce a thick modified layer by means of the thermal diffusion. Meanwhile plasma ion heating is more recently developed by Ronghua Wei et al[1]. Therefore the temeperature is a critical parameter in plasma ion processing. In this paper we present the theoretical model and analysize the effect of imlantation voltage, plasma density, ion mass,etc on the temperature rise.
关键词:
plasma immersion ion implantation
,
null
,
null
夏小建
量子电子学报
doi:10.3969/j.issn.1007-5461.2009.06.010
采用Wei-Norman方法,求出含时变电压源的介观LC电路随时间演化的精确解,应用相空间准概率分布函数,研究了时变电源作用下介观LC电路相干态的量子特性,结果表明此函数是一个二维运动的Gauss波包,其中心电量和磁通呈余弦和正弦变化.
关键词:
量子光学
,
LC回路
,
介观电路
,
相干态
,
量子态演化
,
相空间的准概率分布函数
材料科学技术（英文）
The effect of interstitial hydrogen on the cohesion of the Al Sigma=11(113) grain boundary (GB) is investigated based on the thermodynamic model of Rice-Wang using the first-principles density function calculation. The results indicate that interstitial H behaves as an embrittler from "strengthening energy" analysis. The reduced GB cohesion due to the presence of H at the GB is attributed to the low affinity between H and Al, and the weakened bonding of Al atomic pairs perpendicular to GB plane.
关键词:
hydrogen;grain boundary;Al-Mg alloys;pseudopotentials;1st-principles
Xiaoguang LIU
,
Xiaowei WANG
材料科学技术（英文）
The effect of interstitial hydrogen on the cohesion of the Al ∑=11(113) grain boundary (GB) is investigated based on the thermodynamic model of Rice-Wang using the first-principles density function calculation. The results indicate that interstitial H behaves as an embrittler from "strengthening energy" analysis. The reduced GB cohesion due to the presence of H at the GB is attributed to the low affinity between H and Al, and the weakened bonding of Al atomic pairs perpendicular to GB plane.
关键词:
Hydrogen
,
null
,
null
WEI Jihe Xi'an Institute of Metallurgy and Construction Engineering
,
China.
材料科学技术（英文）
The oxidation of alloying elements during the ESR of stainless steel has been studied. The model previously developed by WEI and Mitchell for the chemical reactions and mass transfer processes during ESR was applied to the remelting of the high Cr steel 1Cr18Ni9(Ti).The laboratory data for the unsteady state A.C.ESR were analyzed and dealt with by the model.When the remelting process reached a steady state,an oxidant(Fe_2O_3 powder)or a deoxidant(Ca-Si powder or metallic Ca)was added to the slag bath.The results showed that this model is applicable to the remelting of stainless steel rather precisely, and it is expected that the model may offer a reliable basis for the control of composition during practical ESR of high alloy steel. Also,the oxidation of Cr in the steel must be noticed when its content is high;but it is entirely possible to adjust the Cr content of ingot within a considerable range,using a special technique by means of the slag-metal reactions during the remelting.
关键词:
ESR
,
null
,
null
,
null
,
null
